Nicolas Müller

Mr. Nicolas Müller

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 July 2023 in Drones
Verified
Journal Article
Open access
PDF file
MGMauro Ghirardelli
Mauro Ghirardelli
SKStephan Kral
Stephan Kral
NMNicolas Müller
Nicolas Müller
Richard HannRichard Hann
Richard Hann
Etienne CheynetEtienne Cheynet
Etienne Cheynet
JRJoachim Reuder
Joachim Reuder
This study presents a computational fluid dynamics (CFD) based approach to determine the optimal positioning for an atmospheric turbulence sensor on a rotary-wing uncrewed aerial vehicle (UAV) with X8 configuration. The vertical (zBF) and horizontal (xBF) distances of the sensor to the UAV center to reduce the effect of the propeller-induced flow are investigated by CFD simulations based on the k−ϵ turbulence model and the actuator disc theory. To ensure a realistic geometric design of the simulations, the tilt angles of a test UAV in flight were measured by flying the drone along a fixed pattern at different constant ground speeds. Based on those measurement results, a corresponding geometry domain was generated for the CFD simulations. Specific emphasis was given to the mesh construction followed by a sensitivity study on the mesh resolution to find a compromise between acceptable simulation accuracy and available computational resources. The final CFD simulations (twelve in total) were performed for four inflow conditions (2.5 m s−1, 5 m s−1, 7.5 m s−1 and 10 m s−1) and three payload configurations (15 kg, 20 kg and 25 kg) of the UAV. The results depend on the inflows and show that the most efficient way to reduce the influence of the propeller-induced flow is mounting the sensor upwind, pointing along the incoming flow direction at xBF varying between 0.46 and 1.66 D, and under the mean plane of the rotors at zBF between 0.01 and 0.7 D. Finally, results are then applied to the possible real-case scenario of a Foxtech D130 carrying a CSAT3B ultrasonic anemometer, that aims to sample wind with mean flows higher than 5 m s−1. The authors propose xBF=1.7 m and zBF=20 cm below the mean rotor plane as a feasible compromise between propeller-induced flow reduction and safety. These results will be used to improve the design of a novel drone-based atmospheric turbulence measurement system, which aims to combine accurate wind and turbulence measurements by a research-grade ultrasonic anemometer with the high mobility and flexibility of UAVs as sensor carriers.

28 February 2026 in Drones
Verified
Journal Article
Open access
PDF file
NMNicolas Müller
Nicolas Müller
EVEric Villeneuve
Eric Villeneuve
Richard HannRichard Hann
Richard Hann
Ice accretion is a significant threat to the operation of UAVs in cold climates. This study analyzed the performance degradation caused by ice accretion on a propeller with a diameter of 0.53 m for a small UAV in an icing wind tunnel. Three different droplet diameters of 20, 40, and 60 µm were tested along with three liquid water contents between 0.28 g/m3 and 1.12 g/m3 along with temperatures of −5 °C, −10 °C, and −15 °C. Additionally, the influence of the variation in the rotation rate was measured. The droplet diameter was observed to have the strongest influence on the propeller’s performance. An increase in the median volume diameter from 20 µm to 40 µm was correlated with a significant decrease in the propeller’s performance. After a minute of icing, the experiment at 20 µm showed a reduction in thrust of 25% compared to a decrease in thrust by 100% for the 40 µm case and 120% for the 60 µm case, meaning that the propeller is not generating thrust, but is generating drag. The temperature influences the propeller’s performance, with the most substantial performance degradation at −5 °C and a decrease in the performance impact with a temperature reduction. Analyzing the performance impact is an important step for deploying UAVs in icing conditions by detecting the most critical conditions for the performance of a UAV propeller. The analysis shows that the most critical conditions are at −5 °C and that an increase in droplet diameter and liquid water content leads to more severe icing conditions. The results show the need for future analysis comparing the performance impact of a propeller at different icing wind tunnels and the validation of numerical methods for predicting the performance degradation of a UAV propeller.