In this paper, we experimentally demonstrate a cost-efficient real-time field programmable gate array (FPGA)-based system for underwater optical wireless communication (UOWC) at a data rate up to 25 Mb/s over a 10 m underwater channel. The transmitter of the system employs a commercial blue LED as a modulation light source and an FPGA unit for transmitter baseband signal processing, and an avalanche photo diode cascaded with an FPGA unit for receiver baseband signal processing at the receiver side. We also suggest a simplified system model to characterize underwater optical link. Three types of hard-decision forward error correction codes are introduced to investigate the impact on the receiver sensitivity in long distance transmission cases. By adding additional link attenuation, we experimentally measure the attenuation coefficients for different water conditions. Based on the measured results, the achievable link distance for clear ocean water is estimated up to 118 m at the transmitted electrical power of 30 dBm. The proposed UOWC system takes both implementation complexity and cost into consideration and also provides a significant guidance to the future real-time high-speed underwater optical communications.
We experimentally demonstrate a 3.61 Pbit/s generalized mutual information (GMI) estimated throughput by space division multiplexing (SDM) and wavelength division multiplexing (WDM) combined transmission over 19-core single-mode fiber. Covering 17 THz bandwidth with a 25-GHz grid in S, C, and L band, 680 wavelength channels are used to deliver 24.5 GBaud probabilistically constellation-shaped (PCS) 256 quadrature amplitude modulation (QAM) and PCS-64QAM signals. The measured data rate shows a great potential for S/C/L-band transmission to dramatically enhance the achievable data rate in multi-core fibers.
The surging growth in data traffic has necessitated the development of higher-speed, lower-latency intensity modulation and direct detection (IM/DD) passive optical networks (PONs) with higher power budgets. To address the inherent limitations of traditional silica-based solid-core fibers, anti-resonant hollow-core fibers have garnered significant attention from both academia and industry. In this Letter, we present an experimental demonstration of 100 Gb/s PAM-4 IM/DD PON transmission over a 20 km anti-resonant hollow-core fiber in the C band, utilizing low-complexity digital signal processing (DSP). The result achieves a record high power budget of 42.5 dB, facilitated by a 3-tap weighted lookup table (LUT) at the optical line terminal (OLT) side and a semiconductor optical amplifier used as a preamplifier at the optical network unit (ONU) side. This represents the highest power budget reported for IM/DD PON to date, to the best of our knowledge, and offers a promising alternative for the future evolution of PON systems.
Random lasers (RLs), which possess peculiar advantages (e.g., emission and coherence tunable) over traditional lasers with optical resonators, have witnessed rapid development in the past decades. However, it is still a challenge to tune the lasing peak of an RL over a wide range. Here, a temperature-dependent Förster resonance energy transfer (FRET) RL is demonstrated in pyrromethene 597 (PM597, “donor”) and Nile blue (NB, “acceptor”) doped chiral liquid crystals. By changing the temperature that drives the liquid crystal bandgap shift, our RL device exhibits a lasing output change from 560 nm (yellow) to 700 nm (red). While the intrinsic FRET efficiency between PM597 and NB is relatively low, the red lasing is weak. By introducing gold nanorods (GNRs) into these RL devices and utilizing GNRs’ localized surface plasmon resonance (LSPR) effect, the efficiency of FRET transfer is increased by 68.9%, thereby reducing the threshold of the RL devices. By tuning the longitudinal LSPR to match the emission wavelength of NB, the best 200-fold lasing intensity enhancement is recorded. Our findings open a pathway toward realizing LSPR-enhanced FRET tunable RLs and broaden the range of their possible exploration in photonics research and technologies.
Based on its ultra-low backscattering characteristic, anti-resonant hollow-core fiber is a good medium for bidirectional transmission, which means that the wavelengths of the transmission channels are the same in both directions. In this Letter, we present the first, to the best of our knowledge, demonstration of S + C + L-band same-wavelength bidirectional transmission in an anti-resonant hollow-core fiber. By using a commercial real-time coherent optical transceivers and amplified spontaneous emission (ASE) source, a total net throughput of 273.6 Tbit/s is achieved over 1.4 km nested anti-resonant nodeless fiber (NANF) with 19.65 THz bandwidth and bidirectional wavelength division multiplexing (WDM) transmission. Commercial 400 G, 1 T, and 800 G optical modules are employed in the S-band, C-band, and L-band, respectively. We experimentally evaluate the same-wavelength bidirectional WDM transmission performance by verifying 2 × 102 channels of 68 Gbaud probabilistically constellation-shaped (PCS) 16 quadrature amplitude modulation (QAM) in the S-band with 75 GHz grid, 2 × 48 channels of 118 Gbaud PCS-64QAM in a C-band with 125 GHz grid and 2 × 60 channels of 91.6 Gbaud PCS-64QAM in the L-band with 100 GHz grid. All 420 test channels could satisfy the bit error ratio (BER) requirements. The result shows great potential for same-wavelength bidirectional WDM transmission in an anti-resonant hollow-core fiber.
We address the optimal transmission of LED-based visible light communication (VLC) system using direct current biased optical orthogonal frequency division multiplexing (DCO-OFDM) modulation and avalanche photodiode (APD) receiver. The peak-to-average-power ratio (PAPR) characteristic of O-OFDM signal is studied, which reveals that the careful setting of transmission parameters is necessary for O-OFDM signal with high PAPR to avoid the severe nonlinear distortion. We further experimentally investigate the nonlinear distortion caused by the LED clipping and APD module saturation, and define a modified term called signal-to-noise and distortion ratio (SNDR) to measure the influence of nonlinear distortion on system performance. The derived explicit expression of SNDR shows that the performance depends on the transmission parameters of both direct current bias Vdc and peak-to-peak voltage Vpp. Meanwhile the sequential quadratic programming algorithm is applied to maximize SNDR and obtain the optimal transmission parameters. The optimal transmission of the nonlinear LED-VLC system is achieved via both simulations and experiments.