The Euphrates River, a vital water resource in Iraq, has seen a marked decline in flow over the past two decades due to climate change and upstream interventions. The aim of this study is to investigate the impacts of changing rainfall patterns and temperature on the river's water balance, flow regime, and drought index. Results show an annual rainfall decline of 0.15 mm, while maximum and minimum temperatures increased annually by 0.086°C and 0.066°C, respectively, according to the Mann-Kendall trend and Sen’s slope tests. Monthly rainfall generally decreased, except for slight increases in April (0.32 mm) and October (0.018 mm). July 2017 and August 2003 saw peak temperatures of 45.1°C, while January 2008 recorded a minimum of -1.8°C. The box-and-whisker plot revealed high rainfall variability in November and February. River flow dropped by 41%, mainly due to the Turkish GAP project and climate impacts. HEC-DSS software analyzed flow duration over 32 years, and Pearson’s correlation showed low associations between flow rate and temperature (-0.36) and rainfall (0.29). The Drinc program was utilized to calculate the Standardized Drought Index, which identified that the water year 1987–1988 was very wet, while it detected severe droughts in 2014–2015 and 2021–2022. Overall, climate change and upstream dam construction have significantly reduced Euphrates River discharges, intensifying drought conditions in the region. The long-term changes in precipitation and air temperature in the study area support the observed streamflow trends. The findings of this study demonstrate that a cooperative approach to international water management between the riparian states is crucial.
2 December 2020 in Journal of Water and Land Development
River training structures; such as submerged groynes are low profile linear structures that are generally located on the outside bank to form groynes fields and prevent the erosion of stream banks by keeping a flow away from it. In the present research, the maximum scour depth was measured based on laboratory experiments where different shapes of submerged groynes (I-shape, L-shape, T-shape) were used as sort of countermeasures to investigate about most shapes that reduce the scour around them. The result of submerged groynes showed a clear decrease in scour depth ratio due to increasing sub-merged ratio and increase the scour hole geometry with increasing of flow intensity, and also Froude number. The maxi-mum scour hole in this research was observed at T-shape groyne and then followed by I-shape groyne and L-shape groyne. The maximum scour depth that cased by I-shape was more than L-shape by a percentage about 8.2%, and it was less than T-shape by a percentage about 16.4%.
Piano key weirs (PKWs) with crown parapet walls effectively manage water levels and maximize storage. However, their efficiency is compromised by interactions between water flow and submerged outlets during rising water levels. This study investigates novel parapet wall designs to improve PKW performance and reduce submergence effects. The experiment focuses on a PKW with a fixed 12.6 cm weir height. Three parapet wall configurations are tested: Mode 1 (walls on all apex), Mode 2 (walls fixed on sides and inlet), and Mode 3 (walls along the sides). Each mode includes three parapet wall profiles: rectangular (consistent form), triangular, and trapezoidal (varying characteristics). Results indicate that parapet wall design significantly affects water level variations with increasing wall height. Mode 3, featuring triangular and trapezoidal parapet walls, demonstrates the highest discharge capacity among the examined profiles. The discharge coefficient correlates with parapet wall height and form. Notably, the triangular wall in Mode 3 outperforms Modes 1 and 2 when parapet walls maintain an R/P ratio of 0.36. This study introduces innovative parapet wall designs to enhance PKW efficiency. By implementing advanced configurations, significant improvements in water control and discharge capacity can be achieved. These findings contribute to the state-of-the-art in PKW technology and offer valuable insights for practical engineering applications.
Water supply, energy production, flood control, and irrigation are all possible uses for embankment dams. Seepage is one of the primary reasons for the embankment dam failure. Numerical analysis and computer tools are commonly used to simulate a diversity of seepage flow conditions in earth dams. An embankment dam’s numerical analysis is a procedure in which the challenge is represented in the real world and explained in abstract form. The major numerical techniques typically utilized in the field of computational mechanics are the finite difference (FD), finite element (FE), and boundary element (BE). The use of mathematical modeling to predict seepage in earth dams was presented in this work. MODFLOW, GOESTUDIO, ANSYS, PLAXIS, PDEase2D, SVFLUX, and other software used to analyze embankment dams were covered.
This article focuses on the United States Bureau of Reclamation (USBR) Type II stilling basin, which has chute blocks, an end dentated sill, and a flat floor. USBR provides general design criteria to contain the hydraulic jump within the stilling basin. The sequent depth ratio, energy dissipation ratio, and stilling basin dimensions of the hydraulic jump are changed when the bed slope of USBR II stilling basins is changed. This study aimed to investigate the effects of adverse slope on the performance of USBR II stilling basin in terms of sequent depth ratio and energy dissipation. Six discharges ranging from 8 to 33 lps were applied to the USBR II stilling basin with bed slopes (S) of −0.085, −0.055, −0.035, and 0. Results demonstrated that forQ= 13 and 8 lps, the basin performs better than other models withS= −0.085, increasing energy dissipation by about 10% compared to a typical basin due to the formation of a free hydraulic jump downstream dentated end sill. On the other hand, the floor downstream of the dentated end sill needs more protection against this free jump, and this case becomes economically expensive. In other cases, the downstream jump was submerged, resulting in a counterintuitive current and reverse roller based on the submerged ratio, reducing the effectiveness of the stilling basin. In addition, the modified design of the stilling basin resulted in a shorter effective length that included the hydraulic jump downstream spillway, thereby reducing internal friction. As a result, the standard USBR II with a flatbed is less expensive and more efficient than the adverse slope basin.