Warm deformation is a plastic-forming process that differs from traditional cold and hot forming techniques. At the macro level, it can effectively reduce the problem of high deformation resistance in cold deformation and improve the surface decarburization issues during the hot deformation process. Microscopically, it has significant advantages in controlling product structure, refining grain size, and enhancing product mechanical properties. The Gleeble-1500D thermal–mechanical physical simulation system was used to conduct isothermal compression tests on GCr15 bearing steel. The tests were conducted at temperatures of 600–1050 °C and strain rates of 0.01–5 s⁻¹. Based on the experimental data, the critical strain model and dynamic recrystallization model for the warm–hot forming of GCr15 bearing steel were established in this paper. The model accuracy is evaluated using statistical indicators such as the correlation coefficient (R). The dynamic recrystallization model exhibits high predictive accuracy, as indicated by an R-value of 0.986. The established dynamic recrystallization model for GCr15 bearing steel was integrated into the Forge^® 3.2 numerical simulation software through secondary program development to simulate the compression process of GCr15 warm–hot forming. The dynamic recrystallization fraction was analyzed in various deformation regions. The grain size of the severe deformation zone, small deformation zone, and difficult deformation zone was compared based on simulated compression specimens under the conditions of 1050 °C and 0.1 s⁻¹ with the corresponding grain size obtained with measurement based on metallographic photos; the relative error between the two is 5.75%. This verifies the accuracy of the established dynamic recrystallization and critical strain models for warm–hot deformation of GCr15 bearing steel. These models provide a theoretical basis for the finite element method analysis and microstructure control of the warm–hot forming process in bearing races.

A precise constitutive model is the foundation and key to finite element simulation in material volume forming and the optimization of the hot working process. Hence, to build a precise constitutive model, a method based on a genetic algorithm (GA) for the inverse optimization identification of parameters is presented in this paper. The idea of this method is to continuously adjust the model parameters through GA until the objective function reaches the minimum value. In this study, hot compression experiments were performed on the Gleeble-1500D thermal simulator at temperatures ranging from 800 °C to 1000 °C and strain rates of 0.01 s⁻¹ to 1 s⁻¹. The Arrhenius-type (A-T) model considering strain compensation and the Johnson–Cook (JC) model considering the coupling effects of strain, temperature and strain rate were constructed, respectively, by using the regression method and the parameter inverse optimization identification method. For the purposes of comparing and verifying the reliability of the predictions of the two established constitutive models, the correlation coefficient (R), average absolute relative error (AARE), and relative error (RE) were adopted. The results show that both the optimized A-T model and the optimized JC model have high prediction accuracy. Compared to the optimized JC model, the optimized A-T model demonstrated a higher correlation coefficient, by 0.003, and a lower average absolute relative error, by 1.43%. Furthermore, the relative error distribution of the optimized A-T model was found to be more concentrated than that of the optimized JC model. These results suggest that the A-T model is more appropriate than the JC model for characterizing the high-temperature deformation behavior of Ti6Al4V alloy.

Ti6AL4V alloy is widely used in the biomedical and energy vehicle industries, among others. Ti6Al4V alloy cannot be fabricated at ambient temperatures; hence, it requires hot forming. However, this method is susceptible to crack defects. The crack defect problem of Ti6AL4V alloy in the hot-forming process cannot be ignored, so we must develop a precise hot-forming damage prediction model. In this study, three high-temperature damage models of Ti6Al4V alloy were developed, considering the temperature and strain rate. These models were derived from the normalized Cockcroft and Latham (NCL), Oyane, and Rice and Tracey (RT) damage models. The damage parameters of the models were identified using a genetic algorithm combined with finite element simulation. The force accumulation error of the Ti6AL4V alloy specimen, which was obtained from a simulated thermal tensile test and an actual test, was used as an optimization target function. Then, the damage parameters were optimized using the genetic algorithm until the target function reached the minimum value. Finally, the optimal damage model parameter was obtained. Through program development, the three high-temperature damage models established in this paper were embedded into Forge^® NxT 2.1 finite element software. The simulated thermal tensile test of Ti6AL4V alloy was performed at a temperature of 800–1000 °C and a strain rate of 0.01–5 s⁻¹. The simulated and actual fracture displacements of the tensile specimens were compared. The correlation coefficients (R) were calculated, which were 0.997, 0.951, and 0.912. Of the high-temperature damage models, the normalized Cockcroft and Latham high-temperature damage model had higher accuracy in predicting crack defects of Ti6Al4V alloy during the hot-forming process. Finally, a fracture strain graph and a high-temperature damage graph of Ti6Al4V alloy were constructed. The Ti6Al4V alloy damage evolution and thermal formability were analyzed in relation to the temperature and strain rate.