Wastewater from the tofu industry contains many pollutants that are very harmful to the environment, significantly endangering aquatic life and producing a pungent odor. This study aims to prepare a polyvinylidene fluoride (PVDF) membrane with the additive polyvinylpyrrolidone (PVP), and utilize it to treat tofu wastewater in the ultrafiltration (UF) process. Flat sheet membranes were prepared using PVDF that was dissolved in N,N-dimethylacetamide (DMAc) and then combined with the additive material of PVP at the varying compositions of 14.9/0.1, 14.85/0.15, and 14.8/0.2 g of PVDF/gram of PVP. The addition of PVP was proposed to improve the properties of the membranes. Characterization by scanning electron microscope (SEM), water contact angle, and Fourier transform infrared spectroscopy (FTIR) were performed on the PVDF/PVP membrane flat sheet in order to understand and compare changes in the physical and chemical properties that occurred in the membrane. Prior to the UF process, the tofu wastewater was treated by a coagulation–flocculation process through a jar tester using poly aluminum chloride (PAC) as a coagulant. Based on the membrane characterization, the addition of PVP improved the physical and chemical properties of membranes. The pore size of the membrane becomes larger, which could increase permeability as well as the flux value. The TSS and turbidity of the water produced in the UF process decreased with an increase in feed pressure due to a greater driving force generated to facilitate the penetration of the suspended solids. The UF results showed that the effect of PVP on water flux was greatest for the 14.85/0.15 PVDF/PVP membrane for both pure and wastewater. In addition, the highest percentage of rejection for TSS and turbidity were observed in the 14.9/0.1 PVDF/PVP membrane and rejection for TDS was indicated in the 14.8/0.2 PVDF/PVP membrane. Meanwhile, the resulting pH decreased slightly across all samples as feed pressure increased.
The oil and gas industry and related applications generate large quantities of oily wastewater, which can adversely affect the environment and human health if not properly handled. This study aims to prepare polyvinylidene fluoride (PVDF) membranes incorporated with polyvinylpyrrolidone (PVP) additives and utilize them to treat oily wastewater through the ultrafiltration (UF) process. Flat sheet membranes were prepared using PVDF dissolved in N,N-dimethylacetamide, followed by the addition of PVP ranging from 0.5 to 35 g. Characterization by scanning electron microscopy (SEM), water contact angle, Fourier transform infrared spectroscopy (FTIR), and mechanical strength tests were performed on the flat PVDF/PVP membranes to understand and compare the changes in the physical and chemical properties of the membranes. Prior to the UF process, oily wastewater was treated by a coagulation–flocculation process through a jar tester using polyaluminum chloride (PAC) as a coagulant. Based on the characterization of the membrane, the addition of PVP improves the physical and chemical properties of the membrane. The membrane’s pore size becomes larger, which can increase its permeability and flux. In general, the addition of PVP to the PVDF membrane can increase the porosity and decrease the water contact angle, thereby increasing the membrane’s hydrophilicity. With respect to filtration performance, the wastewater flux of the resultant membrane increases with increasing PVP content, but the rejections for TSS, turbidity, TDS, and COD are reduced.
17 August 2021 in International Journal of Chemical Engineering
NOx (NO and NO2) are air toxins that endanger life and represent a hazard to the environment, such as photochemical smog, global warming, acid rain, ozone depletion, and the occurrence of respiratory infections. Some technological strategies to diminish NOx emissions to meet regulations depend on two techniques: the dry process and the wet process. This study applies polyvinylidene fluoride (PVDF) hollow fiber membrane modules as a medium to remove NOx from solutions containing several absorbents such as hydrogen peroxide and nitric acid (H2O2-HNO3) solutions, sodium chlorite and sodium hydroxide (NaClO2-NaOH) solutions, and sodium chlorate and sodium hydroxide (NaClO3-NaOH) solutions. The experimental results showed that the oxidants strength influences NOx removal efficiency, where the absorbent solutions containing hydrogen peroxide had the highest removal efficiency as hydrogen peroxide is the most potent oxidant, followed by sodium chlorite and sodium chlorate. The three pairs of absorbents also gave a high NOx removal efficiency (above 90), which means that all the absorbents used in the study are very potential to be used to diminish NOx via the wet process. NOx removal efficiency at the same feed gas flow rate increased as the number of fiber and absorbent concentrations is increased. However, NOx removal efficiency is reduced as the feed gas flow rate is increased at the same membrane module and absorbent concentration.