Field-effect transistors (FETs) based on two-dimensional materials (2DMs) with atomically thin channels have emerged as a promising platform for beyond-silicon electronics. However, low carrier mobility in 2DM transistors driven by phonon scattering remains a critical challenge. To address this issue, we propose the controlled introduction of localized tensile strain as an effective means to inhibit electron-phonon scattering in 2DM. Strain is achieved by conformally adhering the 2DM via van der Waals forces to a dielectric layer previously nanoengineered with a gray-tone topography. Our results show that monolayer MoS2 FETs under tensile strain achieve an 8-fold increase in on-state current, reaching mobilities of 185 cm²/Vs at room temperature, in good agreement with theoretical calculations. The present work on nanotopographic grayscale surface engineering and the use of high-quality dielectric materials has the potential to find application in the nanofabrication of photonic and nanoelectronic devices.
23 February 2024 in Microsystems & Nanoengineering
Grayscale structured surfaces with nanometer-scale features are used in a growing number of applications in optics and fluidics. Thermal scanning probe lithography achieves a lateral resolution below 10 nm and a vertical resolution below 1 nm, but its maximum depth in polymers is limited. Here, we present an innovative combination of nanowriting in thermal resist and plasma dry etching with substrate cooling, which achieves up to 10-fold amplification of polymer nanopatterns into SiO2 without proportionally increasing surface roughness. Sinusoidal nanopatterns in SiO2 with 400 nm pitch and 150 nm depth are fabricated free of shape distortion after dry etching. To exemplify the possible applications of the proposed method, grayscale dielectric nanostructures are used for scalable manufacturing through nanoimprint lithography and for strain nanoengineering of 2D materials. Such a method for aspect ratio amplification and smooth grayscale nanopatterning has the potential to find application in the fabrication of photonic and nanoelectronic devices.
Strain is a proven technique for modifying the bandgap and enhancing carrier mobility in 2D materials. Most current strain engineering techniques rely on the post‐growth transfer of these atomically thin materials from growth substrates to target surfaces, limiting their integration into nanoelectronics. Here, we present a new approach where strain in 2D materials is already introduced directly during their growth on grayscale‐patterned topographies instead of flat surfaces. Both strain levels and orientations are deterministically engineered by controlling grayscale surface contour lengths through thermal expansion mismatches in nanostructured stacks, where the conformally grown and firmly attached 2D material is forced to match the underlying morphology change during cooling. With this method, we experimentally demonstrate precise control of localized tensile strain from 0 to 0.5% in grown MoS 2 monolayer along both uni‐ and multiaxial directions, while higher strain levels are shown to be theoretically possible. This strain‐engineered growth of 2D material films directly on the target substrates is a generic and adaptable approach to various combinations of grayscale‐thin‐film/substrates and eliminates all the transfer‐related limitations of previous approaches, thus paving the way for integrating strained 2D materials into next‐generation nanoelectronics.
Field-effect transistors (FETs) based on two-dimensional materials (2DMs) with atomically thin channels have emerged as a promising platform for beyond-silicon electronics. However, low carrier mobility in 2DM transistors driven by phonon scattering, remains a critical challenge. To address this issue, we propose the controlled introduction of localized biaxial tensile strain as an effective mean to inhibit electron-phonon scattering in 2DM. Strain is achieved by conformally adhering the 2DM via van-der-Waals forces to a dielectric layer previously nanoengineered with a gray-tone topography. Our results show that a monolayer MoS2 FETs under tensile strain achieves an 8-fold increase in on-state current reaching mobilities of 185 cm2/Vs at room temperature, in good agreement with theoretical calculations. The present work on nanotopographic grayscale surface engineering and the use of high-quality dielectric materials has the potential to find application in the nanofabrication of photonic and nanoelectronic devices.
Grayscale structured surfaces with nanometer-scale features are used in a growing number of applications in optics and fluidics. Thermal scanning probe lithography achieves a lateral resolution below 10 nm and a vertical resolution below 1 nm, but its maximum depth in polymers is limited. Here, we present an innovative combination of nanowriting in thermal resist and plasma dry etching with substrate cooling, which achieves up to 10-fold amplification of polymer nanopatterns into SiO2 without additional surface roughness. Sinusoidal nanopatterns in SiO2 with 400 nm pitch and 150 nm depth are fabricated free of shape distortion after dry etching. To exemplify the possible applications of the proposed method, grayscale dielectric nanostructures are used for scalable manufacturing through nanoimprint lithography and for strain nanoengineering of 2D materials. Such method for high aspect ratio and smooth grayscale nanopatterning has the potential to find application in the fabrication of photonic and nanoelectronic devices.