The seismic wave finite-difference numerical simulation of fluid–solid coupled media in a marine environment has many challenges, such as the accuracy of the forward modeling, ripple-shaped scattering at an irregular seabed and inaccurate travel-time. In this paper, a seismic forward-modeling method for fluid–solid coupled media (FSCM) with a transition layer is proposed. The second-order acoustic wave pressure equation and the second-order elastic wave displacement equation in heterogeneous media are used in the fluid and solid media, respectively. To improve the accuracy and stability of seismic wave propagation simulation in FSCM, the first-order displacement–stress elastic wave equation is used as the transition layer to convert the pressure and displacement at the fluid–solid coupled interface, then a method for connecting the transition layer, the upper media and the lower media is presented. To overcome the ripple-shaped scattering in the irregular interface of the seabed, we resample the model to capture the seabed interface accurately, and use the Kaiser windowed |${\rm{sinc}}$| function filter to interpolate the resampled model to match the original mesh grid. This produces accurate reflected travel-time information while suppressing the ripple-shaped scattering. Finally, various models were tested to confirm the stability of the proposed method and the solution to the scattered-waves artifact problem.
The marine environment can be considered as a fluid-solid coupled media governed by the acoustic-elastic coupled equation (AECE). For complex fluid-solid coupled models with irregular seabeds, the well-known finite-difference method (FDM) often causes ripple-shaped scattering due to the rectangular grid. To overcome this problem, a meshless method (MM), called the generalized finite-difference method (GFDM), for irregular node distributions is developed and applied to AECE forward modeling by using a body-fitted node-generation method, which provides robust node distributions for GFDM. Compared with the FDM, our GFDM improves modeling accuracy and eliminates divergence. Furthermore, our MM was applied to an AECE-based elastic full-waveform inversion (EFWI). Owing to the well-matched irregular seabed, our EFWI can invert the accurate elastic model for ocean-bottom cable and pressure data. Numerical examples demonstrate that this method can efficiently improve the numerical accuracy and build an accurate velocity model even using noisy data, which is helpful for high-precision seismic exploration in the complex marine environment.
Elastic full-waveform inversion (EFWI) updates high-resolution model parameters by minimizing the misfit function between the observed and modeled data. EFWI possesses strong nonlinearity and is likely to converge to a local minimum when the inversion begins with inaccurate initial models. Elastic reflection waveform inversion (ERWI) recovers the low-wavenumber components of P- and S-wave velocities along the “rabbit ear” wavepaths to provide initial velocity models for EFWI. However, every iteration of ERWI requires six times as many forward calculations with elastic-wave equations, which can be computationally expensive. Hence, we have developed a pure-wave reflection waveform inversion (PRWI) approach, which sequentially inverts low-wavenumber components of P- and S-wave velocity models. In our PRWI, we decompose elastic-wave operators into background and perturbed pure-wave parts and derive PRWI gradients using pure-wave operators. The background and perturbed wavefields in PRWI gradients are vector wavefields with a single wave mode. PRWI can remove the high-wavenumber noise caused by S-wave stress decomposition and reduce the computational cost of ERWI by almost 70%. Under the framework of PRWI, we have further developed the pure-wave reflection traveltime inversion (PRTI) approach to alleviate the issue of cycle skipping caused by waveform mismatch. To ensure the recovery of low-wavenumber components, we mute out the contribution of wavefields with small opening angles to PRTI gradients. Numerical examples have demonstrated that our PRTI method can efficiently provide good initial velocity models for EFWI.
Onshore seismic exploration analyzes seismic wave propagation in elastic media, which includes the conversion between P- and S-waves. The development of multi-wave and multi-component seismic exploration methods provides data that enable onshore elastic wave full-waveform inversion. However, most data sets of onshore exploration are single component obtained from the particle-motion response from the vertical geophone. When the aiming area has a low-velocity zone, the ray path of reflected wave that propagates to the detector is nearly perpendicular to the ground surface, so that we call it P-wave data. In this paper, we focus on multi-parameter waveform inversion using P-wave reflection seismic data. Although only P-wave data are received, it still contains the converted P-wave information, and the converted P-wave energy gradually increases as the offset increases. As seismic acquisition technology, observation systems and science develop, the folds and acquisition offset increase significantly, and the seismic data contain important converted P-wave information. In this paper, the first-order elastic velocity–stress equation is decomposed to obtain the scalar-P-wave equation from which the S-wave velocity is included firstly. Then we present the theoretical framework for onshore multi-parameter full-waveform inversion using P-wave data. In order to explore the inversion potential of the P-wave data (extracting the S-wave velocity from the converted P-wave information) and accuracy and stability of the P- and S-wave velocity inverted by our method, we carry out numerical tests via different inversion strategies, by using the P-wave data regarded as containing converted P-wave information, and get successful results.