The hydrogen internal combustion engine offers the opportunity to achieve similar performance and comfort characteristics as a conventional gasoline fuelled engine. In order to improve power density and vehicle range new ways in engine design and in charging hydrogen engines were investigated.The en
25 October 2004 in SAE International Journal of Advances and Current Practices in Mobility
Using the regenerative fuel hydrogen in a vehicle's internal combustion engine application requires not only a custom engineered combustion concept, but also optimized operation strategies. That enables the availability of high power output as well as the abolition of critical exhaust gas emissions in combination with high efficiencies. The direct injection hydrogen internal combustion engine offers the potential to achieve higher performance and dynamic characteristics than a conventional gasoline fuelled engine. A specially designed single cylinder test engine equipped with external and internal mixture formation systems was used to investigate the potentials of a combined operation of DI (direct-injection) and PFI (port fuel injection) and the effects of various injection pressures. With direct injection high load operation at stoichiometric mixtures was possible. Maximum engine power output could be increased by more than 20 % above a conventional gasoline engine in combination with an indicated efficiency of more than 33 %. At low engine loads lean operation using external mixture formation was investigated. With this strategy indicated fuel efficiencies of more than 40 % were achieved. For the entire operating range of the engine, an operation strategy is proposed which enables high power-density, high engine efficiencies as well as lowest environmental impact due to a virtually CO2- and NOx- free operation. Visualization methods were successfully used for enhancing the engines combustion concept layout and to compare with the simulation models used. Simulation tools such as pressure curve analysis, 1-dimensional flow simulation and an engine loss analysis were developed and successfully deployed in designing the current test engines.
A measurement technique for the quantitative investigation of mixture formation processes in hydrogen internal combustion engines (ICEs) has been developed using tracer-based laser-induced fluorescence (TLIF). This technique can be employed to fired and motored engine operation. The quantitative TLIF fuel/air-ratio results have been verified by means of linear Raman scattering measurements. Exemplary results of the simultaneous investigation of mixture formation and combustion obtained at an optical accessible hydrogen ICE are shown.
13 September 2011 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
A complex task regarding the control of the homogeneous charge compression ignition (HCCI) combustion process is the control of combustion timing, represented by the crank angle at which 50 per cent of the fuel mass inside the cylinder is burned (MFB50). The most important parameters for transient MFB50 control are the mass of (hot) residual gas inside the cylinder (e.g. retained by internal exhaust gas recirculation), the injection strategy (in the case of direct fuel injection), and the spark timing. In this paper, the potential of a corona ignition system is examined in comparison with a conventional spark ignition system for the HCCI combustion process. For this purpose, thermodynamic investigations have been carried out on a single-cylinder research engine, combined with one-dimensional gas exchange analyses and high-speed visualization of combustion in a transparent engine. It could be demonstrated that both ignition systems are capable of influencing the autoignition process. The corona ignition system, however, allows a much later ignition point for achieving the same MFB50. This is due to the spatial character of the initial ignition area of corona ignition. In addition, the corona ignition system is more robust with respect to a change in the boundary conditions, such as a variation in the residual gas rate or the mixture composition. It is therefore more reliable in initiating autoignition, even in critical operating conditions. Additionally, it was found that the corona ignition system permits the combustion to be influenced by means of a variation in the ignition energy, which appeared to be not the case for the conventional ignition system.
This work presents an open-source, dynamic, 1D, proton exchange membrane fuel cell model suitable for real-time applications. It estimates the cell voltage based on activation, ohmic and concentration overpotentials and considers water transport through the membrane by means of osmosis, diffusion and hydraulic permeation. Simplified equations reduce the computational load to make it viable for real-time analysis, quick parameter studies and usage in complex systems like complete vehicle models. Two modes of operation for use with or without reference polarization curves allow for a flexible application even without information about cell parameters. The program code is written in MATLAB and provided under the terms and conditions of the Creative Commons Attribution License (CC BY). It is designed to be used inside of a Simulink model, which allows this fuel cell model to be used in a wide variety of 1D simulation platforms by exporting the code as C/C++.