The nanobubbles contained in the human body are induced to collapse by the shock wave, and thus produce a strong impact and high-speed nanojet, resulting in trauma to human tissues. The collapse of nanobubbles in water caused by shock waves is investigated by molecular dynamics. Nanobubbles are divided into three types: vacuum nanobubble, carbon dioxide nanobubble, and oxygen nanobubble. The influence of factors such as the number of gas molecules, the diameter of the nanobubbles, and the impulse of the shock wave on the bubble collapse are considered separately. The results show that the addition of gas molecules to vacuum nanobubbles does not affect the propagation of shock waves. However, before the nanobubbles are completely collapsed, the maximum velocity of the nanojet formed by the collapse of nanobubbles containing 718 carbon dioxide molecules (or 733 oxygen molecules) is larger than that of vacuum and nanobubbles containing 1368 carbon dioxide molecules (or 1409 oxygen molecules). After the nanobubbles are completely collapsed, the gas molecules cause the velocity of the nanojet to decay, and finally the maximum velocity of the nanojet containing gas molecules is less than that of the vacuum nanojet. In addition, it is also found that the collapse time of nanobubbles is short at high impulse, and the density and pressure when the shock wave passes at the same time are both greater. After the bubble collapses, the maximum velocity of the nanojet is larger, and the impact force is much stronger than that at a small impulse. Larger diameter nanobubble has a longer collapse time, and the density and pressure when the shock wave passes at the same time are both smaller, and the shock wave propagation is slower, but the maximum speed of the nanojet is larger. The impact is stronger. The greater the maximum velocity of the nanojet, the greater the distance that is dispersed by the gas molecules of the gas-containing nanobubbles in the impact direction will be and the deeper the depression.
18 October 2023 in Journal of Vibration and Control
As the switch for the start-up of the nozzle at the rear of the recoilless gun, the opening pressure of the blocking sheet directly affects the balance of the recoilless gun during the shooting process. The opening time of the blocking sheet is obtained through high-speed camera by capturing the tail flame. Using piezoelectric pressure sensors, the pressure at different positions along the barrel were measured. Furthermore, the pressure at the moment of opening the blocking sheet was determined based on its opening time. A significant force jump (Δ f = 146.9 kN) in the unbalanced recoil experienced by the recoilless gun during the initial firing stage was identified based on the theory of one-dimensional recoilless gun balanced interior ballistics. This jump arises from the opening pressure of the blocking sheet surpassing the projectile's starting pressure ( P0). This research can provide a reference for the design of recoilless weapons related to unbalanced force.
6 September 2023 in Computer Methods and Programs in Biomedicine
A noise attenuation performance test was conducted on earmuffs using a recoilless weapon launch platform in a confined space, along with two acoustic test fixtures (ATFs). The overpressure at the ATF's effective tympanic membrane comprised direct sound at 185 dB sound pressure level (SPL) and reflected sound at 179 dB SPL. Wearing earmuffs reduced these peaks to 162 dB SPL and 169 dB SPL, respectively. The reflected sound from walls was defined as delayed sound. An analytical model for earmuff noise attenuation simulated their effectiveness. The simulation revealed that when the earmuffs attenuated delayed sound, the acoustic impedance of acoustic leakage and the acoustic impedance of the earmuff material decreased by 96% and 50%, respectively. The negative overpressure zone between direct and delayed sound decreased the earmuffs' fit against the ATF. Additionally, the enclosed volume between the earmuff and the ear canal decreased by 12%. After the installation of bandages on the earmuffs, the overpressure peak of delayed sound was reduced by 5 dB. Furthermore, the acoustic impedance of the earmuff's sound leakage path and the acoustic impedance of the earmuff material deformation path increased by 100% and 809%, respectively.
Accurately predicting the drift of spinning projectiles in the highland region has always been a challenging task. The study combines genetic algorithm, modified mass ballistic model, and data from ballistic tests to establish a computational model of projectile plateau drift, which is able to compute the value of projectile drift accurately. The reliability of the model was verified by the tests. The study also explains the reasons for the formation of projectile drift and the characteristics of plateau drift through theory. The results of the study proved that under the same range, the projectile's yaw of repose angle is larger in the plateau region, but its projectile plateau drift is smaller mainly because the flight time of the projectile on the highland is smaller than that on the plains. The results of the study are of great significance for the precision strike of projectiles in the highland area.
During the firing process of a recoilless gun, there is a high-intensity pulse noise phenomenon in its rear breech area. In order to obtain the physical mechanism of the pulse noise formation, this article designed experiments and used high-speed cameras and overpressure sensors to discover a “three peaks” phenomenon in the pulse noise at the shooter’s position. Using resistance strain sensors, the changes of strain with time in the chamber and nozzle expansion section of the recoilless gun during the firing process were recorded. By comparing the micro-strain data and overpressure data, the shock waves at the shooter’s position can be categorized into two types: internal shock waves and external shock waves. Internally, the opening of the blocking sheet initiates the formation of the initial shock wave, followed by the formation of a second pressure wave within the combustion chamber. The peak-to-peak interval between these two shock waves is nearly fixed, and the ratio of the dual peaks increases with the distance of the measurement position. The third shock wave forms externally to the nozzle, induced by the explosion of unburned propellant. As the weapon’s distance from the ground increases, the peak values of the overpressure data decrease, and the waveform of this explosion-induced shock wave transitions from a single-peak phenomenon to a double-peak phenomenon. This study can provide a reference for the study of the potential risk of injury to operators using single soldier recoilless guns and similar weapons.