Li Yi

Li Yi


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
JCJunying Chen
Junying Chen
TYTao Yang
Tao Yang
FCFirst103 Chen
First103 Chen
QJQingshan JIANG
Qingshan JIANG
LYLi Yi
Li Yi
ZXZhilong Xu
Zhilong Xu
Ultrasonic rolling is an effective technique for enhancing surface integrity, and surface integrity is closely related to fatigue performance. The process parameters of ultrasonic rolling critically affect the improvement of surface integrity. This study proposes an optimization method for process parameters by combining machine learning (ML) with the NSGA-II. Five ML models were trained to establish relationships between process parameters and surface residual stress, hardness, and surface roughness by incorporating feature augmentation and physical information. The best-performing model was selected and integrated with NSGA-II for multi-objective optimization. Ultrasonic rolling tests based on a uniform design were performed, and a dataset was established. The objective was to maximize surface residual stress and hardness while minimizing surface roughness. For test specimens with an initial surface roughness of 0.54 µm, the optimized process parameters were a static pressure of 900 N, a spindle speed of 75 rpm, a feed rate of 0.19 mm/r, and rolling once. Using optimized parameters, the surface residual stress reached −920.60 MPa, surface hardness achieved 958.23 HV, surface roughness reduced to 0.32 µm, and contact fatigue life extended to 3.02 × 107 cycles, representing a 52.5% improvement compared to untreated specimens and an even more significant improvement over without parameter optimization.

2 December 2022 in Coatings
Verified
Journal Article
Open access
PDF file
CXChen Xiuyu
Chen Xiuyu
JSJie Sun
Jie Sun
ZXZhilong Xu
Zhilong Xu
JCJunying Chen
Junying Chen
QJQingshan JIANG
Qingshan JIANG
JCJun Cheng
Jun Cheng
Laser shock peening (LSP) process parameters have an important influence on the strengthening effect. In this study, theoretical calculations were used to determine a suitable range of stress wave peaks (5.09 GPa–6.36 GPa) for laser shocking, which consider the material properties of alloy steel 40Cr. In addition to theoretical calculations, the finite element numerical simulation of a single-point laser shock was also performed. The residual stresses of specimens under different shock pressure waves were simulated, and then the optimal pulse width was determined as 20 ns and the optimal pulse energy was determined as 10 J. Finally, the influences of different pulse energies on the microhardness, residual stress, microstructure, and shock-affected layer thickness of metallic materials were comprehensively investigated through experiments, and the optimization of the laser shock energy was proved to be 10 J. An optimized combination of parameters of a single-point laser shock for 40Cr was obtained, in which the spot diameter was 3 mm, the pulse width was 20 ns, and the pulse energy was 10 J. The study has implications for the selection of LSP process parameters for alloy steels.

29 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
JSJie Sun
Jie Sun
JLJiayuan Li
Jiayuan Li
CXChen Xiuyu
Chen Xiuyu
ZXZhilong Xu
Zhilong Xu
YLYuru Lin
Yuru Lin
LYLi Yi
Li Yi
As a new surface treatment technology, laser shock peening (LSP) is a multi-point overlay process of single-point laser shock. In this study, the finite element method (FEM) was used to build a model of single-point laser shock, and the model was verified by experiments. The difference in residual stresses between the experimental and simulated results was less than 20%. Then, the effects of the stress field and deformation of 20CrMnTi with different laser shock parameters were simulated and analyzed. According to the mechanical response of 20CrMnTi to different laser shock parameters, the optimal shocking process parameters for single-point shocking via LSP were determined to be a shock energy of 5 J, a laser pulse width of 20 ns, and an impact number of 5. Lastly, a simulation of multi-point laser shock was performed with the optimal parameters, and the residual compressive stress values of multi-point impacts are close to those of single-point impacts under the same process conditions.

22 August 2023 in Coatings
Verified
Journal Article
Open access
PDF file
HXHuanbin Xu
Huanbin Xu
LYLi Yi
Li Yi
ZXZhilong Xu
Zhilong Xu
JCJun Cheng
Jun Cheng
CXChen Xiuyu
Chen Xiuyu
ZZZhenye Zhao
Zhenye Zhao
The service life of the cutter ring of the shield tunneling machine affects the efficiency and cost of its tunneling. However, traditional heat treatment processes cannot simultaneously optimize both impact toughness and surface hardness, often leading to cracks or excessive wear of the cutter ring, greatly reducing their service life. According to the above situation, this paper applies high-energy composite modification treatment to H13 steel samples commonly used for the cutter ring of the hob and analyzes the impact toughness, hardness, microstructure, residual stress, and morphology characteristics of fracture of the samples under different high-energy composite modification processes. The study also investigates the effects of high-energy composite modification processes on the hardness and impact toughness of the samples. The experimental results show that the high-energy composite modification process enables the specimens to have good impact toughness and surface hardness simultaneously. The H13 steel sample has the best performance after carburizing, quenching, and laser shock modification, with a maximum surface hardness of 1017.5HV0.2 and an impact toughness of 15.64 J/cm2. Laser shock modification improves the surface residual compressive stress and hardness of H13 steel samples and also improves their impact toughness.

9 September 2024 in Coatings
Verified
Journal Article
Open access
PDF file
CXChen Xiuyu
Chen Xiuyu
YLYalong Li
Yalong Li
LLLonghui Li
Longhui Li
HXHuanbin Xu
Huanbin Xu
LYLi Yi
Li Yi
HLHeng Liu
Heng Liu
Tunnel boring machines (TBMs) are exposed to the impact of the ground shattering force and the friction of sandstone during excavation work, and are prone to wear and breakage, and other failures. Traditional heat treatment processes cannot simultaneously achieve the required high-energy composite structure of hard external and tough internal properties for cutter rings, leading to inadequate wear resistance and impact toughness under working conditions. This study utilizes H13 steel as the base material, and based on a study of carburizing, nitriding, and ultrasonic impact processes for H13 steel analyzing the effects of different high-energy composite modification processes on the hardness distribution, microstructure, and residual stress of H13 steel, the mechanisms by which high-energy composite modification processes affect the wear resistance and impact resistance of H13 steel are revealed. The results indicate that the wear amount and impact toughness of the sample subjected to carburizing and ultrasonic surface rolling composite strengthening were 1.9 mg and 27.34 J/cm2, demonstrating the best wear and impact resistance. This combination of properties allows the H13 steel cutter ring to achieve the optimal overall performance in terms of wear resistance and impact resistance.