Remy FABBRO

Dr. Remy FABBRO

orcid

Research Focus & Metrics

Academic Career Length

37Years (1990-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RFRemy FABBRO
Remy FABBRO
Depending of the laser operating parameters, several characteristic regimes of laser welding can be observed. At low welding speeds, the aspect ratio of the keyhole can be rather large with a rather vertical cylindrical shape, whereas at high welding speeds, low aspect ratios result, where only the keyhole front is mainly irradiated. For these different regimes, the dependence of the keyhole (KH) depth or the keyhole threshold, as a function of the operating parameters and material properties, is derived and their resulting scaling laws are surprisingly very similar. This approach allows us to analyze the keyhole behavior for these welding regimes, around their keyhole generation thresholds. Specific experiments confirm the occurrence and the behavior of these unstable keyholes for these conditions. Furthermore, recent experimental results can be analyzed using these approaches. Finally, this analysis allows us to define the aspect ratio range for the occurrence of this unstable behavior and to highlight the importance of laser absorptivity for this mechanism. Consequently, the use of a short wavelength laser for the reduction of these keyhole stability issues and the corresponding improvement of weld seam quality is emphasized.

1 August 1990
Verified
Conference Paper
Closed access
PDF file
DBDel Solar Bermejo
Del Solar Bermejo
RFRemy FABBRO
Remy FABBRO
LSLilian Sabatier
Lilian Sabatier
LLL Leprince
L Leprince
JOJ M Orza
J M Orza
Some basic aspect concerning spectroscopic determination of electronic density and temperature of high power (1KW to 10KW) laser-induced iron plasmas are discussed. Spatial evolution of the temperature into the key hole and above the target has been measured for different shielding gases and different power densities. At power densities of the order of 1.0-2.0 MW/cm2 the evolution of the temperature with the height over the target depends strongly on the shielding gas. Some spectral lines identified as corresponding to Fe(II) transitions have also been observed. From the measured temperatures and relative intensities ratios between lines corresponding to Fe(I) and Fe(II) , electronic densities have been calculated.

18 August 1997
Verified
Conference Paper
Closed access
PDF file
XSX Scherpereel
X Scherpereel
PPPatrice Peyre
Patrice Peyre
RFRemy FABBRO
Remy FABBRO
GLG Lederer
G Lederer
NCN Celati
N Celati
Laser Shock Processing (LSP) consists on focusing a high energy pulsed laser beam on metals to create shock waves and thereby, generate compressive stresses. These stress are similar to those of conventional mechanical treatments like short peening. Nevertheless, at LSP the affected depths are greater and the surfaces keep their roughness and hardness. The present study compare the effects of LSP on the surface mechanical properties of two stainless steels: an austenitic (AISI 316L) and a martensitic (Z12 CNDV 12.02). The surface effects are characterized in terms of microstructure, hardening and residual stress levels (measured by X-ray diffraction technique). The effects of LSP on the pitting corrosion resistance of the martensitic stainless steel in a NaCl 0.01 M + Na2SO4 0.01 M solution are presented. Electrochemical tests were carried out by using open circuit and polarization techniques, to determine electrochemical parameters (free and pitting potentials, passive current densities). Laser-induced work-hardening effects were shown to be more important in the case of 316 L for which they strongly depend on the impacts repetition and the laser power density. Significant modifications on localized corrosion properties were noticed for each treatment condition (8 GW/cm2 - 20 ns pulses and 40 GW/cm2 - 2,3 ns pulses) i.e. pitting potentials were not modified but free potentials were shifted to anodic values and passive current densities reduced.

1 October 2004
Verified
Conference Paper
Closed access
PDF file
RFRemy FABBRO
Remy FABBRO
SSSonia Slimani
Sonia Slimani
FCFréderic Coste
Fréderic Coste
FBFrancis Briand
Francis Briand
The understanding of keyhole behavior is still a topic of great importance. The keyhole dynamics can be rather easily analyzed in case of full penetration laser welding experiments. Moreover, this configuration can allow an easy access to the complete keyhole geometry, if thin metallic sheets are welded. In that case, one or two laser beam reflections occur on the front keyhole wall. We will present the results of the study of these welding configurations. Several diagnostics have been used. For different experimental conditions, the dynamics of the keyhole and its complete geometry (front wall inclination, top and bottom apertures) have been analyzed by using on axis visualizations through the top and the bottom of the keyhole with a 4 kHz high speed video camera. The measurement of the transmitted laser power gives also an access to the front keyhole wall reflectivity. These results are compared and are used to validate our dynamic keyhole modeling, where ray tracing is included. Finally, for these conditions, an analytical model can be proposed that relates the laser parameters (incident laser power, spot diameter) with the processing parameters (material, sheet thickness and welding velocity) for Nd-Yag laser welding.

1 January 2013
Verified
Book Chapter
Closed access
PDF file
SKSeiji Katayama
Seiji Katayama
STS. Tsukamoto
S. Tsukamoto
RFRemy FABBRO
Remy FABBRO
KLKlaus Löffler
Klaus Löffler
JZJun Zhou
Jun Zhou
JKJens Klsstrup Kristensen
Jens Klsstrup Kristensen