Because of the global trends of energy demand increase and decarbonization, developing green energy sources and increasing energy conversion efficiency are recently two of the most urgent topics in energy fields. The requirements for power level and performance of converter systems are continuously growing for the fast development of modern technologies such as the Internet of things (IoT) and Industry 4.0. In this regard, power switching devices based on wide-bandgap (WBG) materials such as silicon carbide (SiC) and gallium nitride (GaN) are fast maturing and expected to greatly benefit power converters with complex switching schemes. In low- and medium-voltage applications, GaN-based high-electron-mobility transistors (HEMTs) are superior to conventional silicon (Si)-based devices in terms of switching frequency, power rating, thermal capability, and efficiency, which are crucial factors to enhance the performance of advanced power converters. Previously published review papers on GaN HEMT technology mainly focused on fabrication, device characteristics, and general applications. To realize the future development trend and potential of applying GaN technology in various converter designs, this paper reviews a total of 162 research papers focusing on GaN HEMT applications in mid- to high-power (over 500 W) converters. Different types of converters including direct current (DC)–DC, alternating current (AC)–DC, and DC–AC conversions with various configurations, switching frequencies, power densities, and system efficiencies are reviewed.

The optimal planning of electric vehicle (EV) charging stations (ECSs) with advanced control algorithms is very important to accelerate the development of EVs, which is a promising solution to reduce carbon emissions of conventional internal combustion engine vehicles (ICEVs). The large and fluctuant load currents of ECSs can bring negative impacts to both EV-related power converters and power distribution systems if the energy flow is not regulated properly. Recent review papers related to EVs found in open literature have mainly focused on the design of power converter-based chargers and power interfaces, analyses of power quality (PQ) issues, the development of wireless charging techniques, etc. There is currently no review paper that focuses on key technologies in various system configurations, optimal energy management and advanced control issues in practical applications. To compensate for this insufficiency and provide timely research directions, this paper reviews 143 previously published papers related to the aforementioned topics in recent literature including 17 EV-related review papers found in Institute of Electrical and Electronics Engineers (IEEE)/Institution of Engineering and Technology (IET) (IEEE/IET) Electronic Library (IEL) and ScienceDirect OnSite (SDOS) databases. In this paper, existing system configurations, related design methods, algorithms and key technologies for ECSs are systematically reviewed. Based on discussions given in the reviewed papers, the most popular ECS configuration is a hybrid system design that integrates renewable energy (RE)-based power generation (REBPG), various energy storage systems (ESSs), and utility grids. It is noteworthy that the addition of an ESS with properly designed control algorithms can simultaneously buffer the fast, fluctuant power demand during charging, smooth the intermittent power generation of REBPG, and increase the overall efficiency and operating flexibility of ECSs. In addition, verifying the significance of the flexibility and possible profits that portable ESSs provide in ECS networks is a potential research theme in ECS fields, in which the potential applications of portable ESSs in the grid-tied ECSs are numerous and could cover a full technical spectrum.

Wide-bandgap (WBG) material-based switching devices such as gallium nitride (GaN) high electron mobility transistors (HEMTs) and silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFETs) are considered very promising candidates for replacing conventional silicon (Si) MOSFETs for various advanced power conversion applications, mainly because of their capabilities of higher switching frequencies with less switching and conduction losses. However, to make the most of their advantages, it is crucial to understand the intrinsic differences between WBG- and Si-based switching devices and investigate effective means to safely, efficiently, and reliably utilize the WBG devices. This paper aims to provide engineers in the power engineering field a comprehensive understanding of WBG switching devices’ driving requirements, especially for mid- to high-power applications. First, the characteristics and operating principles of WBG switching devices and their commercial products within specific voltage ranges are explored. Next, considerations regarding the design of driving circuits for WBG switching devices are addressed, and commercial drivers designed for WBG switching devices are explored. Lastly, a review on typical papers concerning driving technologies for WBG switching devices in mid- to high-power applications is presented.

This work proposes the first hot-polymer fiber Fabry–Perot interferometer (HPFFPI) anemometer for sensing airflow. The proposed HPFFPI is based on a single-mode fiber (SMF) endface that is attached to a UV-cured polymer to form an ultracompact fiber Fabry–Perot microcavity. The proposed polymer microcavity was heated using a low-cost chip resistor with a controllable dc driving power to achieve a desired polymer’s steady-state temperature (T) that exceeds the T of the surrounding environment. The polymer is highly sensitive to variations of T with high repeatability. When the hot polymer was cooled by the measured flowing air, the wavelength fringes of its optical spectra shifted. The HPFFPI anemometers have been experimentally evaluated for different cavity lengths and heating power values. Experimental results demonstrate that the proposed HPFFPI responses well in terms of airflow measurement. A high sensitivity of 1.139 nm/(m/s) and a good resolution of 0.0088 m/s over the 0~2.54 m/s range of airflow were achieved with a cavity length of 10 μm and a heating power of 0.402 W.

This paper presents a novel design method in which a dual-polymer fiber Fizeau interferometer (DPFFI) is proposed for simultaneously measuring relative humidity (RH) and temperature (T). Since the polymer is intrinsically highly sensitive to both RH and T, the polymer fiber Fizeau interferometer (PFFI) exhibits cross-sensitivity of RH and T. In general, it is difficult to demodulate the optical responses from both variations of RH and T using a single PFFI. If two PFFIs with different structures are combined, they will individually exhibit distinct sensitivity responses with respect to RH and T, respectively. The technical problem of analyzing multiple interferences of the optical spectra of the DPFFI and the individual sensitivity of RH and T to each PFFI is obtained using the fast Fourier transform (FFT). A mathematical method is applied to solve the simultaneous equations of the DPFFI, so that the two variables RH and T can be determined at the same time. Experimental results, indicating good sensitivity and accuracy, with small measurement errors (average errors of ~1.46 °C and ~1.48%, respectively), are shown, determining the feasibility, and verifying the effectiveness, of the proposed DPFFI sensor.

This work proposes a novel, highly sensitive, and simple structure based on a tapered polymer as a tilt fiber sensor to sensitively measure tilt angles (θ). The fiber-optic tilt sensor consists of a tapered polymer and single-mode fibers (SMF), into which the tapered polymer to generate a bent in the sensor that is strongly correlated with θ. The used tapered polymer in the tilt sensing is the temperature (T) insensitive. It is further combined with a general fiber Bragg grating (FBG) as a temperature indicator for achieving simultaneous measurement of inclination (θ) and ambient T. The endface of the fiber is coated with a gold film to increase the light reflectivity and improve the measurement range. Experimental results show that when the sensor tilts, the reflective optical power changes significantly with high sensitivity, and the peak wavelength of FBG shifts when T varies. Both parameters can be measured simultaneously with good discrimination. An average tilt angle sensitivity of approximately 4.23 dB/deg. and a high resolution of 0.009 deg. are achieved in a θ variation from −6 to +6 deg. Simulations were performed and the numerical results were in good agreement with the experimental measurement.