Changheon Song

Dr. Changheon Song

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 November 2019 in Journal of Mechanical Science and Technology
Verified
Journal Article
Closed access
PDF file
DKDae-Ji Kim
Dae-Ji Kim
JOJoo-Young Oh
Joo-Young Oh
JCJung-Woo Cho
Jung-Woo Cho
JKJaewon Kim
Jaewon Kim
Jintai ChungJintai Chung
Jintai Chung
CSChangheon Song
Changheon Song

1 January 2020 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
DKDae-Ji Kim
Dae-Ji Kim
JKJaewon Kim
Jaewon Kim
BLBooyeong Lee
Booyeong Lee
MSMin-Seok Shin
Min-Seok Shin
JOJoo-Young Oh
Joo-Young Oh
CSChangheon Song
Changheon Song
This study suggests a method for quantitatively estimating the drilling performance of the down‐the‐hole (DTH) hammer during percussive drilling of rock surfaces. A pneumatic dynamic model of the DTH hammer was developed that considers the mass flow rate relations representing the orifice opening areas of the air tube, the piston, and bit flushing channels. A drill bit motion model was developed to represent the dynamics of a drill bit impacted by a dropped piston and explain the impact stress propagation and rock‐crushing mechanism. The rock‐crushing effect of the drill button bit was measured through a piston drop test. The pneumatic hammer model and drill bit motion model were then combined in a prediction model to determine the impact efficiency according to different rock types (i.e., soft, medium‐hard, and very hard). The drilling efficiency was defined as the input value of the prediction model, which was used to simulate the drilling performance of DTH hammers considering the rock type and dynamic effect of the drill bit. Finally, the simulation results were compared with the results of in situ drilling tests for verification.

21 May 2021 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
DKDae-Ji Kim
Dae-Ji Kim
HKHoon Kang
Hoon Kang
CSChangheon Song
Changheon Song
JOJoo-Young Oh
Joo-Young Oh
JCJung-Woo Cho
Jung-Woo Cho
JRJamal Rostami
Jamal Rostami

5 October 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DKDaeji Kim
Daeji Kim
HPHyune-Jun Park
Hyune-Jun Park
JOJoo-Young Oh
Joo-Young Oh
JCJung-Woo Cho
Jung-Woo Cho
Jintai ChungJintai Chung
Jintai Chung
CSChangheon Song
Changheon Song
This study aimed to estimate impact loads delivered to vibro-ripper housing through link modules, together with loads transmitted in various directions. Housing vibration resulting from impact loads generated during the operating condition and frequency response functions were assessed by vibration and modal experiments, respectively. Vibration data and transfer functions were applied in a transfer path analysis (TPA) model to analyze the quantified impact loads transmitted through the key components of the vibro-ripper to its housing. Impact loads derived by TPA for different housing parts were compared with those in the tooth derived from load-cell measurements, validating the TPA method. As a result of the verification, the impact load calculated by the TPA method was 193.7 kN, whereas that from the striking force measured by the load cell was 220 kN, a difference of 12.3%. The results of this study may be important input values for numerical analysis in equipment design and can be used as key data for structural safety evaluation and optimization. In summary, this paper introduces the vibration-based TPA method and considers its applicability to construction machinery exposed to impact vibration and loads.

29 October 2026 in Actuators
Verified
Journal Article
Open access
PDF file
DKDaeji Kim
Daeji Kim
HPHyune-Jun Park
Hyune-Jun Park
JOJoo-Young Oh
Joo-Young Oh
JCJung-Woo Cho
Jung-Woo Cho
CSChangheon Song
Changheon Song
A tilt-rotator increases the reachable workspace of a hydraulic excavator, but its configuration also changes structural load paths. This study developed a structural-load-aware work-path planner for a 14-ton excavator using nominal analytical soil loads and an experimentally correlated multibody dynamics model. A full-factorial combination of five tilt angles, five rotation angles, and nine excavation positions yielded 225 candidate motions. The 147 retained motions had predicted peak stresses of 98.5–149.0 MPa. These stresses informed action features and reward penalties in an action-conditioned dueling deep Q-network. Excavated cells became non-traversable holes; the planner incorporated in-place turning and conditional posture-repeat constraints. In the 9 × 9 obstacle environment, the stress-informed agent’s selected route required 44 actions and 452 s of simulated time, compared with 47 actions and 458 s for its stress-uninformed counterpart; cumulative peak-stress indices were 3158.0 and 3361.8 MPa, respectively. In the 5 × 5 environment, its route required one additional action and had a 4.2% higher index. A 21 × 28 site-derived numerical environment was completed in 453 actions, including 280 excavations. The method supports comparative structural-load assessment for construction-machinery safety and future integration with machine-stability criteria. These single-seed comparisons neither establish statistical superiority nor validate machine stability.