Enhancement of the adsorption performance and recyclability of adsorbents is a crucial aspect of water treatment. Herein, we used one-dimensional porous boron nitride (PBN) as a carrier to load Fe3O4 nanoparticles for the preparation of Fe3O4 nanoparticles-functionalized porous boron nitride (Fe3O4/PBN) via a ball milling method. The high-energy ball milling promoted the creation of a negatively charged PBN surface and facilitated the uniform distribution of Fe3O4 nanoparticles on the surface of PBN. The adsorption performance of Fe3O4/PBN toward cationic dyes could be significantly improved while no enhancement was observed for anionic dyes. The great adsorption performance of Fe3O4/PBN is due to its surface functional groups and surface defects formed in the ball milling process. Moreover, the strong interaction force between Fe3O4/PBN and cationic dyes promotes rapid initial adsorption due to their negatively charged surface. Magnetic measurements demonstrated that Fe3O4/PBN is superparamagnetic. The composites with low loadings of Fe3O4 nanoparticles could be quickly separated from the aqueous solution under a low applied magnetic field, improving their recyclability. This work highlights the role of ball milling in improving the adsorption performance of Fe3O4/PBN and greatly promotes the practical application of Fe3O4/PBN in the field of environmental purification.
The excellent temperature stability and high saturation polarization of Bi0.5Na0.5TiO3 (BNT) make it a promising candidate for energy storage capacitors. However, its disadvantages, such as low breakdown strength, high remnant polarization, and a complex sintering process, limit its further development. To address this, (1 − x) Bi0.5Na0.5TiO3−x Sr(Mg1/3Nb2/3)O3 ceramics were fabricated, where ion doping was employed to modify the domain structure, reduce the grain size, and improve the energy storage performance. With the increase in dopant concentration, the evolution from long-range-ordered ferroelectric micro-domains into short-range-ordered randomly oriented polar nanoregions (PNRs) was revealed, as demonstrated by XRD and Raman spectroscopy. This resulted in a diffuse phase transition peak and a significant reduction in remnant polarization. However, the saturation polarization also decreased. Finally, the optimal energy storage performance was achieved at a medium dopant concentration (x = 0.10), accompanied by reduced grain size and a dense microstructure. This composition exhibited a discharged energy density of 1.64 J/cm3 at a low electric field of 150 kV/cm, representing a notable improvement over pure BNT, which showed a highly lossy P-E loop and a discharged energy density of only 0.14 J/cm3 at the same electric field.
The adsorption properties of two kinds of metal–organic frameworks (MOFs), PCN-228ʹ and PCN-230, have been studied by the grand canonical Monte Carlo (GCMC) method for the absorption of N2, H2, CH4/H2 mixed gas. Their pore size distributions are analysed by the Horvath-Kawazoe (HK) method. The PCN-230 exhibits an outstanding volumetric density for hydrogen storage endowed by its ultralow density and promising pore volume. While the PCN-228ʹ shows a great selectivity of 70 towards adsorption of the CH4/H2 gas mixture at low pressure, this type of MOF presents strong CH4 adsorption capacity, which is suitable for CH4/H2 mixed gas separation and purification.
Continued development of lithium-ion batteries is limited by the shortage of Li element. In this situation, the exploration of high-performance sodium-ion batteries is attracting much attention. In this experimental work, Na2/3Ni1/4Mn34O2 film cathode materials were fabricated by excimer laser deposition at different oxygen partial pressures. X-ray diffraction studies and field emission scanning electron microscopy revealed high c-axis orientation and uniform grain distribution, respectively, in the deposited films. Furthermore, after 30 cycles under a current density of 13 mA g−1, the film samples deposited at an oxygen partial pressure of 65 Pa exhibited a high capacity-retention of 91%. The film structure also had a large-current discharge performance, which makes practical applications possible.