Sebastian Springer

Sebastian Springer


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
WSWolfgang Schneller
Wolfgang Schneller
Martin LeitnerMartin Leitner
Martin Leitner
SSSebastian Springer
Sebastian Springer
FGFlorian Grün
Florian Grün
MTMichael Taschauer
Michael Taschauer
This study shows the effect of hot isostatic pressing (HIP) on the porosity and the microstructure, as well as the corresponding fatigue strength of selectively-laser-melted (SLM) AlSi10Mg structures. To eliminate the influence of the as-built surface, all specimens are machined and exhibit a polished surface. To highlight the effect of the HIP treatment, the HIP specimens are compared to a test series without any post-treatment. The fatigue characteristic is evaluated by tension-compression high cycle fatigue tests under a load stress ratio of R = −1. The influence of HIP on the microstructural characteristics is investigated by utilizing scanning electron microscopy of micrographs of selected samples. In order to study the failure mechanism and the fatigue crack origin, a fracture surface analysis is carried out. It is found that, due to the HIP process and subsequent annealing, there is a beneficial effect on the microstructure regarding the fatigue crack propagation, such as Fe-rich precipitates and silicon agglomerations. This leads, combined with a significant reduction of global porosity and a decrease of micro pore sizes, to an improved fatigue resistance for the HIPed condition compared to the other test series within this study.

Verified
Journal Article
Open access
PDF file
WSWolfgang Schneller
Wolfgang Schneller
Martin LeitnerMartin Leitner
Martin Leitner
SPSebastian Pomberger
Sebastian Pomberger
SSSebastian Springer
Sebastian Springer
FBFlorian Beter
Florian Beter
FGFlorian Grün
Florian Grün
This paper focusses on the effect of hot isostatic pressing (HIP) and a solution annealing post treatment on the fatigue strength of selectively laser melted (SLM) AlSi10Mg structures. The aim of this work is to assess the effect of the unprocessed (as-built) surface and residual stresses, regarding the fatigue behaviour for each condition. The surface roughness of unprocessed specimens is evaluated based on digital light optical microscopy and subsequent three-dimensional image post processing. To holistically characterize contributing factors to the fatigue strength, the axial surface residual stress of all specimens with unprocessed surfaces is measured using X-ray diffraction. Furthermore, the in-depth residual stress distribution of selected samples is analyzed. The fatigue strength is evaluated by tension-compression high-cycle fatigue tests under a load stress ratio of R = −1. For the machined specimens, intrinsic defects like pores or intermetallic phases are identified as the failure origin. Regarding the unprocessed test series, surface features cause the failures that correspond to significantly reduced cyclic material properties of approximately −60% referring to machined ones. There are beneficial effects on the surface roughness and residual stresses evoked due to the post treatments. Considering the aforementioned influencing factors, this study provides a fatigue assessment of the mentioned conditions of the investigated Al-material.

5 September 2023 in Materials
Verified
Journal Article
Open access
PDF file
SSSebastian Springer
Sebastian Springer
Martin LeitnerMartin Leitner
Martin Leitner
TGThomas Gruber
Thomas Gruber
BOBernd Oberwinkler
Bernd Oberwinkler
MLMichael Lasnik
Michael Lasnik
FGFlorian Grün
Florian Grün
Additive manufacturing (AM) techniques, such as wire arc additive manufacturing (WAAM), offer unique advantages in producing large, complex structures with reduced lead time and material waste. However, their application in fatigue-critical applications requires a thorough understanding of the material properties and behavior. Due to the layered nature of the manufacturing process, WAAM structures have different microstructures and mechanical properties compared to their substrate counterparts. This study investigated the mechanical behavior and fatigue performance of Ti-6Al-4V fabricated using WAAM compared to the substrate material. Tensile and low-cycle fatigue (LCF) tests were conducted on both materials, and the microstructure was analyzed using optical microscopy and scanning electron microscopy (SEM). The results showed that the WAAM material has a coarser and more heterogeneous grain structure, an increased amount of defects, and lower ultimate tensile strength and smaller elongation at fracture. Furthermore, strain-controlled LCF tests revealed a lower fatigue strength of the WAAM material compared to the substrate, with crack initiation occurring at pores in the specimen rather than microstructural features. Experimental data were used to fit the Ramberg–Osgood model for cyclic deformation behavior and the Manson–Coffin–Basquin model for strain-life curves. The fitted models were subsequently used to compare the two material conditions with other AM processes. In general, the quasi-static properties of WAAM material were found to be lower than those of powder-based processes like selective laser melting or electron beam melting due to smaller cooling rates within the WAAM process. Finally, two simplified estimation models for the strain-life relationship were compared to the experimentally fitted Manson–Coffin–Basquin parameters. The results showed that the simple “universal material law” is applicable and can be used for a quick and simple estimation of the material behavior in cyclic loading conditions. Overall, this study highlights the importance of understanding the mechanical behavior and fatigue performance of WAAM structures compared to their substrate counterparts, as well as the need for further research to improve the understanding of the effects of WAAM process parameters on the mechanical properties and fatigue performance of the fabricated structures.

4 May 2022 in Metals
Verified
Journal Article
Open access
PDF file
SSSebastian Springer
Sebastian Springer
Martin LeitnerMartin Leitner
Martin Leitner
TGThomas Gruber
Thomas Gruber
BOBernd Oberwinkler
Bernd Oberwinkler
MLMichael Lasnik
Michael Lasnik
FGFlorian Grün
Florian Grün
Wire and arc additively manufactured (WAAM) parts and structures often present internal defects, such as gas pores, and cause irregularities in the manufacturing process. In order to describe and assess the effect of internal defects in fatigue design, this research study investigates the fatigue strength of wire arc additive manufactured structures covering the influence of imperfections, particularly gas pores. Single pass WAAM structures are manufactured using titanium alloy Ti-6Al-4V and round fatigue, tensile specimen are extracted. Tensile tests and uniaxial fatigue tests with a load stress ratio of R = 0.1 were carried out, whereby fatigue test results are used for further assessments. An extensive fractographic and metallographic fracture surface analysis is utilized to characterize and measure crack-initiating defects. As surface pores as well as bulk pores are detected, a stress intensity equivalent ∆Keqv transformation approach is presented in this study. Thereby, the defect size of the surface pore is transformed to an increased defect size, which is equivalent to a bulk pore. Subsequently, the fatigue strength assessment method by Tiryakioğlu, commonly used for casting processes, is applied. For this method, a cumulative Gumbel extreme value distribution is utilized to statistically describe the defect size. The fitted distribution with modified data reveals a better agreement with the experimental data than unmodified. Additionally, the validation of the model shows that the usage of the ∆K modified data demonstrates better results, with a slight underestimation of up to about −7%, compared to unmodified data, with an overestimation of up to about 14%, comparing the number of load cycles until failure. Hence, the presented approach applying a stress intensity equivalent transformation of surface to bulk pores facilitates a sound fatigue strength assessment of WAAM Ti-6Al-4V structures.

11 December 2021 in Welding in the World
Verified
Journal Article
Open access
PDF file
SSSebastian Springer
Sebastian Springer
ARA. Röcklinger
A. Röcklinger
MLM. Leitner
M. Leitner
FGF. Grün
F. Grün
TGT. Gruber
T. Gruber
BOB. Oberwinkler
B. Oberwinkler
This research work focusses on the implementation of a viscoplastic creep model in the thermomechanical simulation of the wire arc additive manufacturing (WAAM) process for Ti-6Al-4 V structures. Due to the characteristic layer by layer manufacturing within the WAAM process, viscoplastic material effects occur, which can be covered by implementing a creep model in the thermomechanical simulation. Experimental creep tests with a wide temperature, load and time range were carried out to examine short-term creep behaviour in particular. A Norton-Bailey creep law is used to accurately fit the experimental data and describe the base material’s creep behaviour. Subsequently, the fitted Norton-Bailey creep law was implemented in the thermomechanical simulation of the WAAM process. Finally, to determine the effect of creep on global distortion and local residual stress state in the substrate, simulations of a simplified linear, three-layer WAAM structure, with and without applying the implemented creep law, were carried out and compared to experimental data. The thermomechanical simulation with implemented creep model reveals a significant improvement in the numerical estimation of distortion and residual stress state in the substrate. The maximum distortion is reduced by about 13% and respectively the mean absolute percentage error between simulation and experiment decreases by about 34%. Additionally, the estimation accuracy with respect to the local residual stress state in the substrate improved by about 10%.

11 March 2023 in Welding in the World
Verified
Journal Article
Open access
PDF file
SSSebastian Springer
Sebastian Springer
BSB. Seisenbacher
B. Seisenbacher
MLM. Leitner
M. Leitner
FGF. Grün
F. Grün
TGT. Gruber
T. Gruber
BOB. Oberwinkler
B. Oberwinkler
For the estimation and further optimization of the residual stress and distortion state in additively manufactured structures during and after the wire arc additive manufacturing (WAAM) process, thermomechanical simulation can be applied as a numerical tool. In addition to the detailed modelling of key process parameters, the used material model and material data have a major influence on the accuracy of the numerical analysis. The material behaviour, in particular the viscoplastic behaviour of the titanium alloy Ti-6Al-4 V which is commonly used in aerospace, is investigated within this work. An extensive material characterization of the viscoplastic material behaviour of the WAAM round specimen is carried out conducting low cycle fatigue (LCF) and complex low cycle fatigue (CLCF) tests in a wide temperature range. An elasto-viscoplastic Chaboche material model is parameterised, fitted, and validated to the experimental data in the investigated temperature range. Subsequently, the material model is implemented in the thermomechanical simulation of a representative, linear ten-layer WAAM structure. To finally determine the effect of the fitted material model on the estimation accuracy of residual stress and distortion, simulation results using the standard material model and the elaborated Chaboche model from this study are compared to experimental data in the substrate. The thermomechanical simulation with the Chaboche model reveals a better agreement with the experimental distortion and residual stress state, whereby the standard material model tends to an overestimation. The estimation accuracy with respect to the maximum distortion is improved from an error of 60% with the standard model to an acceptable error of about 6% using the elaborated model. Additionally, the estimated residual stress state shows a sound agreement to the experimental residual stress in the substrate.