Stergios Mavromatis

Dr. Stergios Mavromatis

Department of Transportation Planning and Engineering, School of Civil Engineering, National Technical University of Athens, 15780 Athens, Greece
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2019 in Accident Analysis & Prevention
Verified
Journal Article
Closed access
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
ALAlexandra Laiou
Alexandra Laiou
George YannisGeorge Yannis
George Yannis

22 January 2016 in Transportation Letters
Verified
Journal Article
Closed access
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
BPBasil Psarianos
Basil Psarianos
PTPavlos Tsekos
Pavlos Tsekos
GKGiorgos Kleioutis
Giorgos Kleioutis
EKEvaggelos Katsanos
Evaggelos Katsanos
The research addresses the safe negotiation of sharp horizontal curves combined with steep longitudinal grades. Instrumented field measurements were carried out utilizing a FWD C-Class passenger car in both upgrade and downgrade directions of travel. Initially, the vehicle was driven in braking mode on adjacent steep grade tangent sections in order to define the peak friction coefficients. During vehicle’s tractive mode, for various speed values, friction data were measured and correlated against a vehicle dynamics model developed by the authors’ as well as the point mass model, in order to examine the interaction between vehicle dynamics and road geometry in such alignments. The findings regarding vehicle speed prediction revealed that the dynamic model, on both upgrades and downgrades, is accurate. On the other hand, the point mass model although more simple, revealed accuracy, of a smaller degree, however, but only on upgrades. Moreover, certain findings are reported among which the fact that steep upgrades are more critical at impending skid conditions as well as the acceleration impact in vehicle’s safety.

1 November 2003 in Journal of Transportation Engineering
Verified
Journal Article
Closed access
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
BPBasil Psarianos
Basil Psarianos
Existing design policies determine the speed variation of vehicles on upgrades solely as a function of specific values: initial speed, grade, and weight to power ratio. This paper establishes a dynamic model that considers in addition the influence of the roadway’s horizontal alignment. The model was validated on both tangents (using existing speed-distance profiles and similar simulation models) and curves (by an existing simulation model and field measurements). The model output was examined on a roadway alignment. It was found that sharp horizontal curves influence the speed of heavy vehicles significantly on mild upgrades. Therefore the conventional speed profile determination has to be supplemented by incorporating the horizontal alignment as well. The proposed model can be used to provide solutions in a more efficient and realistic way than does the current practice.

1 June 2021 in Proceedings of the Institution of Civil Engineers - Transport
Verified
Journal Article
Closed access
BKBehrouz Tavassoli Kallebasti
Behrouz Tavassoli Kallebasti
AKAli Abdi Kordani
Ali Abdi Kordani
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
SBSid Mohammad Boroomandrad
Sid Mohammad Boroomandrad
Rural highway crash analyses have shown that the majority of accidents occur on horizontal curves where the vehicle is exposed to lateral forces, which increase the probability of skidding. Moreover, in cases of compound alignments where curves from the road's horizontal alignment are overlaid with constant grades or vertical curves, the probability of skidding increases due to the increase of the longitudinal force on the vehicle. In this research, by utilising vehicle multi-body simulation modelling, several scenarios are defined to assess the impact when horizontal curves are combined with vertical sag curves for three different kinds of vehicles (sedan, sports utility vehicle and truck). For various speed values, the maximum lateral friction demand between the road surface and vehicle tyres is calculated. Finally, by using regression analysis, a model is presented according to the inputs and outputs of the simulation modelling to determine the maximum lateral friction demand created in various conditions. The results of this research indicate that the maximum lateral friction between the road surface and vehicle occurs when the lower part of the sag vertical alignment is located in the middle of horizontal curve.

1 December 2016 in Transportation Letters
Verified
Journal Article
Closed access
EPEleonora Papadimitriou
Eleonora Papadimitriou
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
BPBasil Psarianos
Basil Psarianos
This paper investigates potential Stopping Sight Distance (SSD) violation on divided highways at left horizontal curves overlapped with crest vertical curves. The authors previously developed a SSD control methodology that relates the 3D configuration to the dynamics of a vehicle moving along the roadway. This methodology is applied for the assessment of critical design parameters related to both demanded and available SSD values. Initially, utilizing control geometric and driver – obstacle values adopted by AASHTO 2011 design policy, SSD inadequacy areas were revealed. Subsequently, on the basis of an explanatory modeling approach for a number of geometry parameters, evaluation of SSD sufficiency was carried out in terms of the probability of SSD inadequacy and the prediction of the object height in order to grant SSD adequacy (amended object height). These models may be useful to researchers and practitioners aiming to evaluate the interaction of the utilized design parameters in terms of SSD inadequacy.

1 September 2017 in Journal of Transportation Engineering, Part A: Systems
Verified
Journal Article
Closed access
Stergios MavromatisStergios Mavromatis
Stergios Mavromatis
EPEleonora Papadimitriou
Eleonora Papadimitriou
BPBasil Psarianos
Basil Psarianos
George YannisGeorge Yannis
George Yannis
An existing vehicle dynamics model was used to define design parameters up to which steady-state cornering conditions apply and consequently lift the restrictions of the point mass model. Besides a passenger car, the motion of a two-axle truck was examined as well for both loaded and unloaded conditions. In order to assess critical safety concerns in terms of vehicle skidding, a range of design speed values paired with control design elements from standard design guidelines as well as certain values of peak friction coefficients were used. The unloaded truck was found to be the most critical vehicle in terms of reaching a maximum constant speed, termed as safe speed. Furthermore, the authors provide modeling examples toward the development of a tool for practitioners to concurrently assess the impact of road geometry and friction in terms of defining the vehicle’s safe speed and, consequently, take certain actions. These actions include the adoption of acceptable arrangements for the above values, as well as scheduling accurate friction improvement programs.