The efficacy of plasma-treated tap water (PTW) for the possible treatment of a mealybug (Planococcus citri) infestation was studied under laboratory conditions. Mealybugs growing on Nerium oleander have been treated using PTW after being transferred to Petri dishes, thus avoiding possible buffering effects that might occur in an in-situ study. When treating tap water with a dielectric barrier discharge for several minutes (1, 3, 5 and 10 min) a distinct acidification of the water can be determined, resulting in a pH value of 1.8 after 10 min treatment. The efficacies of the treated tap water samples were compared to the efficacies achieved using classically acidified water. The classical acidification of tap water was carried out using nitric acid and hydrochloric acid to see any possible influences of the salt of the acid in question. The application of PTW revealed high mortality rates of approx. 90% after an observation period of 24 h. PTW appears promising for the treatment of smaller plant stock and commodities as produced by small scale farmers or in greenhouses as an environmentally friendly substitute or supplement to conventional pesticides.

Wood-plastic composite (WPC) based on a polylactic acid (PLA) matrix is a promising material since it is biobased, degradable, sustainable, and 3D printable. However, due to its coloring, visible layers after 3D-printing, and small build volumes of these printers, a coating or gluing of parts might be required. This study investigates the influence of a dielectric barrier discharge (DBD) plasma treatment of PLA-based WPC to activate the surface and improve, e.g., coating capabilities. X-ray photoelectron spectroscopy (XPS) measurements showed the oxidation of the surface due to the formation of carbonyl and carboxyl groups. Laser scanning microscopy revealed a surface roughening after the treatment. Contact angles of water and diiodomethane decreased significantly after the plasma treatment and the consecutively calculated surface free energy increased. Finally, two practical adhesion tests revealed an improvement of the applied acrylic dispersion coating’s adhesion to the WPC surface: The assigned cross-cut class improved, and the pull-off strength increased from 1.4 to 2.3 N/mm².

In this study, polyester powder based on iso- and teraphthalic acid was deposited with an atmospheric plasma jet. The powder was fed into the effluent plasma zone and deposited on European beech wood (Fagus sylvatica L.), Grand fir (Abies grandis Lindl.) and medium density fiberboard (MDF). The substrates were annealed subsequent to the coating process. To exclude decomposition of the polyester layers by the plasma treatment, the surface chemistry of the layers has been examined by X-ray photoelectron spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FTIR) and compared with the polyester powder reference. Furthermore, topographical investigations were carried out using laser scanning microscopy (LSM). Adhesive strength of the layers was evaluated by dolly test and gloss measurements with a goniophotometer. The deposited layers showed no chemical changes compared to the reference. The adhesive strength of the layer met practical requirements of >1 MPa. It was demonstrated that the deposition of a macroscopic layer is possible without a pretreatment or the usage of additives. Therefore this coating process by atmospheric pressure plasma for wood and wood based materials could represent an environmental-friendly alternative to conventional coating methods.

The photocatalyst bismuth oxide, which is active under visual light, was deposited using an atmospheric pressure plasma jet (APPJ). Sixteen different samples were generated under different parameters of the APPJ to investigate their catalytic activity. The prepared samples were characterized using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), laser scanning microscopy (LSM), and UV–vis diffuse reflectance absorption spectroscopy. The measured data, such as average sample thickness, coverage ratio, phase fraction, chemical composition, band gap, and photocatalytic performance were used for comparing the samples. The XRD analysis showed that the deposition process produced a mixed phase of monocline Bi₂O₃ and tetragonal Bi₂O_2.33. Using the Rietveld refinement method, phase fractions could be determined and compared with the XPS data. The non-stoichiometric phases were influenced by the introduction of nitrogen to the surface as a result of the deposition process. The band gap calculated from the diffuse absorption spectroscopy shows that Bi₂O_2.33 with 2.78 eV had a higher band gap compared to the phases with a high proportion of Bi₂O₃ (2.64 eV). Furthermore, it was shown that the band gap was dependent on the thickness of the sample and oxygen vacancies or loss of oxygen in the surface. All coatings had degraded methyl orange (MO) under irradiation by xenon lamps.

In this study, bismuth oxide powder (Bi₂O₃) was deposited by an atmospheric pressure plasma jet onto borosilicate glass. The layer produced through this method is to be used as a photo catalyst in later applications. The deposited coating was analyzed by X-ray diffraction (XRD) to determine the crystal structure, and X-ray photoelectron spectroscopy (XPS) to analyze the chemical state. The results showed a change in crystal and chemical structure during the deposition process. The morphological properties of the layer were examined with scanning electron microscopy (SEM) and laser scanning microscopy (LSM). The band gap structure of the coating was investigated by UV-Vis spectroscopy. The layer produced by the plasma spraying process consisted of circular multi-phase bismuth oxide droplets (monoclinic Bi₂O₃ and tetragonal Bi₂O_2.33), showing a direct band gap of E_g = 2.72 eV, which allows their use as a photocatalyst.

When exposing food and feedstuff to cold atmospheric pressure plasmas (CAPP), e.g., for decontamination purposes, possible unwanted effects on the contained nutrients might occur. In the present study, we thus concentrated on CAPP-induced degrading effects on different sugars, namely glucose and sucrose. The treatments were performed using admixtures of argon and synthetic air over durations of up to $12\min$. Continuous degradation of sucrose and glucose was determined using ATR-FTIR and XPS analyses. OH stretching bands showed notable broadening in the ATR-FTIR spectra, which possibly indicates reduced crystallinity of the sugars caused by the CAPP treatment. In the fingerprint regions, most bands, especially the more intense C-O bands, showed decreases in peak heights. In addition, two new bands occurred after CAPP treatment. The bands were detectable in the range between 1800 and $1600{\mathrm{cm}}^{-1}$ and potentially can be assigned to C=C and, after comparison with the results of the XPS measurements, O-C=O bindings. The XPS measurements also showed that the O-C=O bonds probably originated from earlier C-O bonds.