Groundwater flow models are usually characterized as being either transient flow models or steady state flow models. Given that steady state groundwater flow conditions arise as a long time asymptotic limit of a particular transient response, it is natural for us to seek a finite estimate of the amount of time required for a particular transient flow problem to effectively reach steady state. Here, we introduce the concept of mean action time (MAT) to address a fundamental question: How long does it take for a groundwater recharge process or discharge processes to effectively reach steady state? This concept relies on identifying a cumulative distribution function, $F(t;x)$, which varies from $F(0;x)=0$ to $F(t;x) \to \infty$ as $t\to \infty$, thereby providing us with a measurement of the progress of the system towards steady state. The MAT corresponds to the mean of the associated probability density function $f(t;x) = \dfrac{dF}{dt}$, and we demonstrate that this framework provides useful analytical insight by explicitly showing how the MAT depends on the parameters in the model and the geometry of the problem. \ud \ud Additional theoretical results relating to the variance of $f(t;x)$, known as the variance of action time (VAT), are also presented. To test our theoretical predictions we include measurements from a laboratory–scale experiment describing flow through a homogeneous porous medium. The laboratory data confirms that the theoretical MAT predictions are in good agreement with measurements from the physical model
This study was designed to assess the potential impact of microplastic (MP) pollution on soil hydrology, specifically in retaining and releasing moisture. Herein, High-Density Polyethylene (HDPE) MP of different sizes (i.e., 0.5–1, 1–3, and 3–5 mm) and shapes (i.e., fiber, film, and fragment) were evaluated for their effects on water retention curve (WRC) of sandy loam soil, chosen for its agricultural relevance and widespread environmental presence of HDPE. Nine contamination scenarios were simulated with a low MP pollution rate, 0.01% w/w. Van Genuchten models were used to assess plant available water (PAW), wilting point (WP), and water holding capacity (WHC). Results showed that studied MP could significantly affect WRC and PAW mainly by changing WHC rather than WP and that this effect varied with MP shape and size. According to the results, fragment MP had the greatest impact on soil WHC by increasing 36.3%, followed by fibers and films by 19.8% and 15.7%. MP particles significantly increased WHC, while WP remained relatively unchanged. An observed trend indicated that the impact on WHC increased with the size of the MP particles. These findings emphasize the need to manage soil MP pollution to protect plant growth, agriculture, and water dynamics.
Current knowledge about the potential impacts of microplastics (MP) on vadose zone hydrology is scarce. The primary goal of this study was to address some of the limitations of previous research by developing more reliable and conclusive statistical evidence to better understand whether MP pollution can potentially cause hydrological impacts. We examined the effects of MP shape (type), as well as the magnitude of pollution (MP/soil mass ratio, λ) on water holding capacity (WHC) and bare soil water evaporation (ER) of fine sand, under controlled laboratory conditions. Three different shapes (types) of MP—fiber (polyacrylic), strand (polymethyl methacrylate), and pellet (acrylonitrile butadiene styrene), with six environmentally relevant MP concentration levels (MP/soil mass ratio), all ≤1.5%, were studied. Statistical regressions and non-parametric analyses of variance (i.e., Kruskal–Wallis analysis) indicate that MP pollution has a substantial potential to change WHC and late-stage evaporation, even at relatively low MP concentrations, but has minimal impacts on early stage evaporation of the studied fine sand. The magnitude of the impacts depends on individual MP shape (type) and concentration, connoting those MP impact mechanisms are complex. These findings suggest that the global issue of growing soil–MP pollution should be regarded as a concerning environmental and water resources stressor that could potentially cause widespread environmental change by altering soil-water dynamics at the watershed scale.
10 May 2023 in Frontiers of Environmental Science & Engineering
Despite extensive research on microplastics (MP) in marine environments, little is known about MP abundance and transport in terrestrial systems. There is, therefore, still little understanding of the main mechanisms driving the substantial transport of MP across different environmental compartments. Storm events can transport MP beyond boundaries, such as from the land to groundwater or the ocean, as has already been discovered for organic carbon transport. Urban stormwater detention ponds are suitable environments to study the impact of stormwater on the environmental fate and transport of MP. Herein, we investigate the longitudinal and vertical distribution of MP within two detention ponds with different physical characteristics. Soil samples were collected at various locations and from multiple depths (surface and subsurface layers) for measuring MP concentrations using fluorescence microscopy. Our findings show that MP are retained more near the inlet of the ponds, and MP of larger sizes were found more abundantly near inlets than outlets. We also found that MP mass and sizes decrease from surface soil to subsurface soil. In the pond, where vegetation (grass root network) was more considerable, MP were found more evenly distributed along the depth. In terms of shape, the fragments were the most abundant MP shape.