The aluminum alloy type 5083, which has high corrosion resistance, excellent weldability, and good strength, is widely used in shipbuilding, automotive, aerospace, and industrial construction. The present paper has the aim of establishing a possible correlation between mechanical properties, structural characteristics, and cavitation erosion properties of the 5083 alloy after applying different heat treatments. Different homogenization heat treatments (350 °C, 450 °C) were applied, each followed by cooling in air and artificial aging at different temperature (140 °C and 180 °C) with three maintenance periods, 1 h, 12 h, and 24 h. The experiments concerning cavitation resistance of the experimental samples were completed in accordance with ASTM G32-2016. The cavitation erosion resistance were determined either by analytical diagrams MDER (or MDE) vs. cavity attack duration, or by measuring the maximum erosion attack by stereomicroscopy and scanning electron microscopy. Finally, the best combination of heat treatments applied to cast aluminum products type 5083 is homogenization at 350 °C followed by artificial aging at 180 °C, at which the highest mechanical characteristics are obtained, a resilience of 25 J/cm2, a grain size of 140–180 μm, and a maximum depth of the erosion MDEmax around 14–17 µm.
It is known that a number of parts that operate in liquid media, such as the propellers of motorboats and pleasure river vessels, as well as the rotors of household pumps and the radiators and pumps in the cooling system of motor vehicles are made, as a rule, of aluminum-based alloy. Research during maintenance leads to the conclusion that, in certain operating conditions, due to the turbulent character of the flow, with pressure drops to below the vaporization level, it inevitably reaches the threshold of cavitation, which manifests itself through its effects, especially through erosion. To increase the lifetime, these alloys are currently subjected to techniques to improve the structure’s resistance to the cyclic stresses of cavitational microjets. Among these techniques are volumetric heat treatments, which lead to changes in the microstructure and mechanical property values, with an effect on the behavior and resistance to cavitation erosion. This paper studies the influence of heat aging treatments on the cavitation erosion behavior of an aluminum alloy type 6082, in the cast state. The heat treatments applied were 140 °C/1 h, 12 h, 24 h and 180 °C/1 h, 12 h, 24 h. The MDEmax and MDERs parameters were determined and a correlation could be made between the values of the mechanical-resilient characteristics and the resistance to cavitation erosion in the case of aluminum alloy 6082.
This paper presents experimental results regarding the development of new alloys from the binary ZnCu and ternary ZnCuMg systems. The alloys had controlled chemical compositions and were annealed at 300 °C and 400 °C, with holding times of 5 h and 10 h, followed by air cooling. Mechanical properties (tensile strength, yield strength, elongation, and elastic modulus) were determined. Structural analysis conducted after different heat treatments revealed that homogenization transforms the dendritic structure into a granular structure with intergranular eutectic presence. Biodegradation behavior showed that the ternary alloy exhibits higher degradation rates than the binary alloy. Applying the homogenization heat treatment has a good influence on the binary alloy only, not on the ternary alloy. Our research shows that that the complex alloying of zinc with copper and magnesium may improve cavitation behavior, doubling both the MDEmax parameter and cavitation resistance expressed by Rcav.
The wastes from polyethylene terephthalate (PET) packaging can be turned into armatures for concrete used in the transports infrastructure (roads with rigid concrete structure, pedestrian and concrete pavements and borders), as well as in the construction of safety elements (support walls, bulwark foundations). This experimental research was meant to create dispersed reinforced concrete with armatures from polyethylene waste, originated from the recycling programmes of PET-type packaging. The experimental programme was aimed at constructing some samples of dispersed reinforced concrete from recycled material coming from polyethylene terephthalate (PET) packaging wastes, their testing to the compressive strength and the comparison of results with the characteristics of the standardised samples of concrete (class C30/37). All the reinforcements used in this work to consolidate the dispersed reinforced concrete type were made from a mix of polyethylene terephthalate (PET) packages, of different types and characteristics, which are found daily in supermarkets and which then reach waste. The choice of a mix of polyethylene terephthalate (PET) packaging was chosen in order to render the general recycling of these types of materials as good as possible.
18 June 2015 in IOP Conference Series: Materials Science and Engineering
The stainless steels Duplex 2205 with austenite and ferrite structure have mechanical characteristics close to those of martensite stainless steels but a better corrosion resistance; these steels are very sensitive on the heat treatments. Present work studies the cavitation erosion for those steels for three different heat treatments: simply quenched, annealed at 475°C post quenching and annealed at 875°C. The researches were undertaken at Timisoara "Politehnica" University in the Laboratory of Material Science and the Laboratory of Cavitation, using the T2 facility which integrally respects the recommendation of ASTM G32- 10 Standard. The best results were obtained with the specimens annealed at 875°C. In comparison with the stainless steel 41Cr4, with very good cavitation erosion qualities, all tested steels presented also good erosion resistance. So, Duplex 2205 steels can be used for details subjected to cavitation. The best results are obtained by increasing both the hardness and the quantity of the structure constituent with better cavitation erosion resistance, in our case the alloyed austenite.
YWoven fiber reinforced concrete is a material, which contains various quantities of polymer materials in composition, in addition to the conventional components of an ordinary concrete (mineral binder - cement, aggregates, water and additives). The present work refers to the concrete in which the reinforcement is made of polymeric materials (polyethylene terephthalate), originated from the recycling programs of PET-type packaging. The experimental program was aimed at constructing some samples of woven fiber reinforced concrete from recycled material coming from PET packaging wastes, their testing to the compression demands and the comparison of results with the characteristics of the standardized samples of concrete (class C30/37). Based on a sufficient number of determinations, certain correlations can be established between the compressive strength of the concrete at 28 days depending on the dosage of components (aggregate, binder, and reinforcement), water / cement ratio, reinforcement volume, etc., essential parameters from a compositional point of view. These correlations, customized by cement type and strength class, are very important to determine - with approximation - to what dosage of components (aggregate, binder, reinforcement) the respective level of compressive strength of concrete is obtained.