Ivan Shishov

Mr. Ivan Shishov

Peter the Great St. Petersburg Polytechnic University, Saint Petersburg, Sankt-Peterburg, Russia
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2020 in Materials Characterization
Verified
Journal Article
Closed access
VMV.V. Mishin
V.V. Mishin
ISIvan Shishov
Ivan Shishov
OSO.N. Stolyarov
O.N. Stolyarov
IKI.A. Kasatkin
I.A. Kasatkin
PGP.A. Glukhov
P.A. Glukhov

Verified
Journal Article
Open access
PDF file
VMVasiliy Mishin
Vasiliy Mishin
ISIvan Shishov
Ivan Shishov
AKAlexander Kalinenko
Alexander Kalinenko
IVIgor Vysotskii
Igor Vysotskii
IZIvan S. Zuiko
Ivan S. Zuiko
K Rustam Kaibyshev
Rustam Kaibyshev
In this work, a finite-element model was elaborated to simulate the thermomechanical behavior of 6061 aluminum alloy during friction-stir welding (FSW). It was shown that FSW-induced deformation is a two-stage process. In addition to the stirring action exerted by the rotating tool probe, the material in the near-surface area of the stir zone also experienced a secondary deformation by the shoulder edge after passage of the welding tool. Both deformation steps were found to be comparable in terms of temperature and strain, but the secondary deformation was primarily concentrated in the near-surface layer. The effects of tool rotation and translation rates on FSW temperature and strain were also systematically examined. Depending on particular welding conditions, the peak welding temperature was predicted to vary from 360 to 500 °C, while the cumulative effective strain was from 12 to 45.

28 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
AKAlexander Kalinenko
Alexander Kalinenko
PDPavel Dolzhenko
Pavel Dolzhenko
SMSergey Malopheyev
Sergey Malopheyev
DYDiana Yuzbekova
Diana Yuzbekova
YBYuliya Borisova
Yuliya Borisova
K Rustam Kaibyshev
Rustam Kaibyshev
The purpose of this study was to investigate the interfacial microstructure that was produced during dissimilar friction stir lap welding (FSW) of 6013 aluminum alloy and Ti-6Al-4V. FSW was conducted under a zero-penetration condition, i.e., the welding tool was plunged exclusively into the upper (aluminum) plate of the dissimilar lap joint. To facilitate the interpretation of microstructural processes, finite element modeling (FEM) was applied to evaluate the temperature field within the weld zone. The FEM simulation revealed a very sharp temperature gradient across the dissimilar interface. This effect was attributed to the generation of FSW heat exclusively within the aluminum part and a relatively low thermal conductivity of titanium. The abrupt temperature drop on the titanium side imposed a strict limitation on the diffusion penetration of aluminum and thus resulted in a relatively thin (~0.5 μm) and discontinuous intermetallic compound. Due to the complex chemical composition of the FSWed aluminum alloy, the diffusion processes also involved alloying elements. Consequently, the evolved intermetallic compound had a complicated chemical composition, with the principal elements being aluminum, titanium, silicon, manganese, and magnesium.

1 October 2014 in Russian Metallurgy (Metally)
Verified
Journal Article
Closed access
PDF file
NKN. G. Kolbasnikov
N. G. Kolbasnikov
VMVasiliy Mishin
Vasiliy Mishin
ISIvan Shishov
Ivan Shishov
IKI. S. Kistankin
I. S. Kistankin
AZA. V. Zabrodin
A. V. Zabrodin
The critical values of the Cockcroft-Latham and Ayada criteria, which are embedded in the Deform-3D software package and can be used to describe the fracture of nanocrystalline beryllium at various stages of warm rolling, are determined. It is shown that excess over these critical values leads to the fracture of beryllium during both simulation and experimental rolling. Nondestructive conditions are developed for multipass warm rolling of beryllium with the minimum number of long-term intermediate high-temperature annealing.

27 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
AKAlexander Kalinenko
Alexander Kalinenko
PDPavel Dolzhenko
Pavel Dolzhenko
SMSergey Malopheyev
Sergey Malopheyev
ISIvan Shishov
Ivan Shishov
VMVasiliy Mishin
Vasiliy Mishin
K Rustam Kaibyshev
Rustam Kaibyshev
This work is part of a wide-ranging study aiming to enhance the technology of dissimilar friction-stir welding of aluminum and titanium. In the previous study, a new approach was proposed that provided an exceptionally narrow intermetallic layer. However, an essential disadvantage of this technique was the significant material softening in the aluminum part. Hence, the present work was undertaken in order to obtain insight into microstructural processes and material flow in the aluminum part. To this end, the stop-action technique was applied. It was found that the microstructural evolution included several stages. Specifically, the initial material underwent the discontinuous static recrystallization in the heat-affected zone. With the approach of the rotating tool, the recrystallized grains experienced continuous dynamic recrystallization, which resulted in grain refinement. The subsequent transportation of material around the rotating tool provided no significant alterations in microstructure. This “superplastic-like” character of material flow was attributed to a dynamic balance between grain refinement and grain coarsening. It was also found that the stirred material experienced a secondary deformation induced by the rotating tool shoulder far behind the welding tool. The concomitant microstructural changes were most pronounced at the upper weld surface and gave rise to a fine-grained layer.

1 March 2019 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
VMVasiliy Mishin
Vasiliy Mishin
PGP.A. Glukhov
P.A. Glukhov
ISIvan Shishov
Ivan Shishov
OSO.N. Stolyarov
O.N. Stolyarov
IKIgor Kasatkin
Igor Kasatkin