This paper presents a piezoelectric energy harvesting circuit, which integrates a Synchronized Switch Harvesting on Inductor (SSHI) circuit and an active rectifier. The major design challenge of the SSHI method is flipping the capacitor voltage at optimal times. The proposed SSHI circuit inserts an active diode on each resonant loop, which ensures flipping of the capacitor voltage at optimal times and eliminates the need to tune the switching time. The diodes of the SSHI circuit are also used as a rectifier to further simplify the controller. The key advantage of the proposed circuit is a simple controller, which leads to low power dissipation of the proposed circuit to result in high efficiency. The proposed circuit is self-powered and capable of starting even when the battery is completely drained. The circuit was fabricated in BiCMOS 0.25 μm technology with a die size of 0.98 × 0.76 mm ² . Measured results indicate that the proposed circuit increases the amount of power harvested from a piezoelectric cantilever by 2.1 times when compared with a full bridge (FB) rectifier and achieves a power conversion efficiency of 85%. The proposed circuit dissipates about 24 μW while the controller alone only 1.5 μW.

This paper presents an ultra low power IC design for piezoelectric (PE) energy harvesting, which integrates a maximum power point tracking (MPPT) circuit and a synchronized switch harvesting on inductor (SSHI) circuit. The proposed circuit also has three different operation modes to extend the range of the harvestable power level generated by a PE transducer. The circuit is designed in CMOS and fabricated in BiCMOS 0.25 μm technology with the die size of 2 mm2. The measurement results indicate the circuit can harvest energy with the input power ranging from 10 μW to 34 μW during MPPT. It achieves peak efficiency of 77 % under a PE cantilever voltage of 3.5 V and the battery voltage of 4.2 V.

This paper presents a piezoelectric (PE) energy harvesting circuit, which integrates a Synchronized Switch Harvesting on Inductor (SSHI) circuit and a diode bridge rectifier. A typical SSHI circuit cannot transfer the power from a PE cantilever into the load when the rectified voltage is higher than a certain voltage. The proposed circuit addresses this problem. It uses the two resonant loops for flipping the capacitor voltage and energy transfer in each half cycle. One resonant loop is typically used for the parallel SSHI scheme, and the other for the series SSHI scheme. The hybrid SSHI circuit using the two resonant loops enables the proposed circuit’s output voltage to no longer be limited. The circuit is self-powered and has the capability of starting without the help of an external battery. Eleven simple discrete components prototyped the circuit. The experimental results show that, compared with the full-bridge (FB) circuit, the amount of power harvested from a PE cantilever and the Voltage Range of Interest (VRI) of the proposed circuit is increased by 2.9 times and by 4.4 times, respectively. A power conversion efficiency of 83.2% is achieved.

In this letter, a direct AC-DC converter for piezoelectric (PE) energy harvesting is proposed, which integrates a Synchronous Switch Harvesting on Inductor (SSHI) circuit, to achieve a resistive impedance matching. An SSHI circuit intends to deal with high impedance of the PE transducer. Then, the converter working in discontinuous conduction mode (DCM), with relative high switching frequency, delivers the harvested energy into the load. The circuit is self-powered and can start even if the storage elements are completely drained. The experimental results show that the proposed circuit has better power extraction capability with a higher output voltage, compared with conventional SSHI rectifier under the same excitation.

This paper presents a piezoelectric (PE) energy harvesting circuit based on the DSSH (double synchronized switch harvesting) principle. The circuit consisted of a rectifier and a DC–DC circuit, which achieves double synchronized switch operation for the PE transducer in each vibration half-cycle. One of the main challenges of the DSSH scheme was precisely controlling the switch timing in the second loop of the resonant loops. The proposed circuit included a MOS transistor in the second loop to address this challenge. It utilized its threshold voltage to manage the stored energy in the intermediate capacitor per vibration half-cycle to simplify the controller for the DSSH circuit. The circuit can operate under either the DSSH scheme or the ESSH (enhanced synchronized switch harvesting) scheme, depending on the value of the intermediate capacitor. In the DSSH scheme, the following DC–DC circuit reused the rectifier’s two diodes for a short period. The prototype circuit was implemented using 16 discrete components. The proposed circuit can be self-powered and started up without a battery. The experimental results showed that the proposed circuit increased the power harvested from the PE transducer compared to the full-bridge (FB) rectifier. With two different intermediate capacitors of 100 nF and 320 nF, the proposed circuit achieved power increases of 3.2 and 2.7 times, respectively. The charging efficiency of the proposed circuit was improved by a factor of 5.1 compared to the typical DSSH circuit.

The traditional SSHI circuit forms a resonant loop to salvage the charges that would otherwise be wasted. However, the quality factor of the loop would be low. This brief presents a triple-bias parallel SSHI rectifier, which can effectively enhance the power extraction capability from the piezoelectric (PE) transducer. The circuit has a low complexity and is easy to integrate, which can convert the original one voltage flipping into a triple per half cycle, thereby improving the voltage flipping ratio for low quality factor. The experimental results show that, compared to the traditional SSHI circuit, the power obtained by the load is boosted up to 1.23 X.