Ceramic-based ferroelectric materials have long been used as functional ferroelectric materials for applications in triboelectric-energy harvesting. However, their drawbacks (brittleness, energy-intensive fabrication methods, and minimal mechanical flexibility) have intensified the search for alternatives where flexible form factors are needed. Molecular ferroelectrics are an emerging class of multifunctional materials. To date, the intriguing piezo/ferroelectric properties of these materials have led to the construction of piezoelectric nanogenerators. However, their numerous advantages warrant their expansion towards triboelectric nanogenerators (TENGs). We aimed to demonstrate the potential of a molecular ferroelectric, diisopropylammonium bromide (DIPAB), in the realm of triboelectric-energy harvesting. Combining ferroelectric properties with enhanced surface modification, we designed an electrospun-based TENG comprising DIPAB/P(VDF-TrFE) as an active negative layer. The synergistic effects emanating from highly aligned polymeric chains and ferroelectric particles in conjunction with a high surface area of the as-designed TENG generated an output voltage of 203.8 V and resulted in a maximum power density of 416.2 mW m−2 when operated in contact separation mode. Its practical application as a sustainable power supply for low-power electronics was demonstrated through powering of commercial electrolytic capacitors and LEDs. This study presents a reliable, cost-effective, and readily scalable method for enhancing TENG performance. This strategy holds potential for application of TENGs in wearable biomechanical-energy harvesting, and paves the way for further advances involving a sustainable energy solution for wearable electronics.
Cyclophosphazenes offer a robust and easily modifiable platform for a diverse range of functional systems that have found applications in a wide variety of areas. Herein, for the first time, it reports an organophosphazene‐based supramolecular ferroelectric [(PhCH2NH)6P3N3Me]I, [PMe]I. The compound crystallizes in the polar space group Pc and its thin‐film sample exhibits remnant polarization of 5 µC cm−2. Vector piezoresponse force microscopy (PFM) measurements indicated the presence of multiaxial polarization. Subsequently, flexible composites of [PMe]I are fabricated for piezoelectric energy harvesting applications using thermoplastic polyurethane (TPU) as the matrix. The highest open‐circuit voltages of 13.7 V and the maximum power density of 34.60 µW cm−2 are recorded for the poled 20 wt.% [PMe]I/TPU device. To understand the molecular origins of the high performance of [PMe]I‐based mechanical energy harvesting devices, piezoelectric charge tensor values are obtained from DFT calculations of the single crystal structure. These indicate that the mechanical stress‐induced distortions in the [PMe]I crystals are facilitated by the high flexibility of the layered supramolecular assembly.
This paper presents a biocompatible flexible pressure sensor fabricated by employing a biocompatible organic ferroelectric, namely, single protonated 1,4-diazabicyclo[2.2.2]octane fluoroborate ([Hdabco]BF 4 ) embedded in poly(vinylidene fluoride) (PVDF) polymer. The presented device generated an output voltage of 6.5 V, which is more than twice the voltage generated by pristine polymeric device. When used as pressure sensor, the device showed a high sensitivity of 0.4 V/kPa and a linear response for external compressive pressures that ranged between 1.6 kPa to 12.8 kPa. These results demonstrate that [Hdabco]BF 4 @ PVDF composite is a promising material for applications such as wearable electronics where biocompatible and self-powered sensors are much needed.
This study explores the surface chemistry and electrical responses of ultra-high-sensitivity SnO2 MEMS arrays to enable a novel sequential detection methodology for detecting nitrogen dioxide (NO2) and ethanol (C2H5OH) as a route to achieve selective gas sensing in electronic nose (E-nose) applications. Utilizing tin oxide (SnO2) thin films deposited via atomic layer deposition (ALD), the array achieves the lowest reported detection limits of 8 parts per billion (ppb) for NO2. The research delves into the detection mechanisms of NO2 and C2H5OH, both individually and in subsequent exposures, assessing the sensor’s dynamic response across various operating temperatures. It demonstrates rapid response and recovery times, with averages of 48 s and 277 s for NO2 and 40 and 48 for C2H5OH. Understanding the role of individual gases on the SnO2 surface chemistry is paramount in discerning subsequent gas exposure behavior. The oxidizing behavior of C2H5OH following NO2 exposure is attributed to interactions between NO2 and oxygen vacancies on the SnO2 surface, which leads to the formation of nitrate or nitrite species. These species subsequently influence interactions with C2H5OH, inducing oxidizing properties, and need to be carefully considered. Principal component analysis (PCA) was used to further improve the sensor’s capability to precisely identify and quantify gas mixtures, improving its applicability for real-time monitoring in complex scenarios.
Molecular ferroelectrics are garnering growing interest across various applications and have only recently been utilized in triboelectric nanogenerators (TENGs). However, their use has largely been confined to uniaxial ferroelectrics, with multiaxial ferroelectrics remaining underexplored. In this work, we introduce a newly constructed Triboelectric Nanogenerator (TENG) based on a multiaxial ferroelectric material, 3,3- difluorocyclobutanammonium hydrochloride ((3,3-DFCBA)Cl), which showcases distinctive traits of multiaxial ferroelectricity, strong piezoelectric coefficient (d33) of 33 pC/N, and remarkable piezoelectric voltage coefficient of (g33) of 437.2 x 10-3 Vm/N, about twice than that of polyvinylidene difluoride (PVDF), making it highly suitable for the emerging field of wearable sensors. Herein, the multiaxial ferroelectric material ((3,3-DFCBA)Cl) was incorporated into a polydimethylsiloxane (PDMS) composite, with electrospun polyvinyl alcohol (PVA) fibers serving as the positive triboelectric layer. The resulting TENG device achieved the highest output voltage of 233 V and a maximum power density of 361 mW/m2 under an optimal load of 20 MΩ for the optimized 10 wt% PDMS/((3,3-DFCBA)Cl) composite device. Additionally, the harvested energy proved effective for capacitor charging applications.