This paper presents a high-precision component-type vertical pendulum tiltmeter based on an FPGA (Field Programmable Gate Array) that improves the utility and reliability of geophysical field tilt observation instruments. The system is designed for rapid deployment and offers flexible and efficient adaptability. It comprises a pendulum body, a triangular platform, a locking motor and sealing cover, a ratiometric measurement bridge, a high-speed ADC, and an FPGA embedded system. The pendulum body is a plumb-bob-type single-suspension wire vertical pendulum capable of measuring ground tilt in two orthogonal directions simultaneously. It is installed on a triangular platform, sealed as a whole, and equipped with a locking motor to withstand a free-fall impact of 2 m. The system utilizes a differential capacitance ratio bridge in the measurement circuit, replacing analog circuits with high-speed AD sampling and FPGA digital signal processing technology. This approach reduces hardware expenses and interferences from active devices. The system also features online compilation functionality for flexible measurement parameter settings, high reliability, ease of use, and rapid deployment without the need for professional technical personnel. The proposed tiltmeter holds significant importance for further research in geophysics.
In this study, an FPGA(Field Programmable Gate Array)-based borehole strain measurement system was designed that makes extensive use of digital signal processing operations to replace analog circuits. Through the formidable operational capability of FPGA, the sampled data were filtered and denoised to improve the signal-to-noise ratios. Then, with the goal of not reducing observational accuracy, the signal amplification circuit was removed, the excitation voltage was reduced, and the dynamic range of the primary adjustments was expanded to 130 dB. The system’s online compilation function made it more flexible to changes in measurement parameters, allowing it to adapt to various needs. In addition, the efficiency of the equipment use was enhanced. The actual observational results showed that this study’s FPGA-based borehole strain measurement system had a voltage resolution higher than 1 μV. Clear solid tides were successfully recorded in low-frequency bands, and seismic wave strain was accurately recorded in high-frequency bands. The arrival times and seismic phases of the seismic waves S and P were clearly recorded, which met the requirements for geophysical field deformation observations. Therefore, the system proposed in this study is of major significance for future analyses of geophysical and crust deformation observations.
Borehole strain gauges play a crucial role in geophysical, seismological, and crustal dynamics studies. While existing borehole strain gauges are proficient in measuring horizontal strains within vertical boreholes, their effectiveness in capturing vertical and oblique strains is limited due to technical constraints arising from the cylindrical probe’s characteristics. However, the accurate measurement of three-dimensional strain is essential for a comprehensive understanding of crustal tectonics, dynamics, and geophysics, particularly considering the diverse geological structures and force sources within the crustal medium. In this study, we present a novel approach to address this challenge by enhancing an existing horizontal-component borehole strain gauge with a bellows structure and line strain measurement technology to enable vertical and borehole oblique strain measurements. Integrating these enhancements with horizontal strain measurement capabilities enables comprehensive three-dimensional borehole strain measurements within the same hole section. The system was deployed and tested at the Gongxian seismic station in Sichuan Province. Clear observations of solid tides were recorded across horizontal, oblique, and vertical measurement units, with the tidal morphology and amplitude being consistent with the theoretical calculations. The achieved measurement sensitivity of 10-10 meets the requirements for borehole strain measurement, enabling the characterization of three-dimensional strain states within boreholes through association methods.
Borehole strainmeters are essential tools for observing crustal deformation. In long-term observational applications, the dynamic changes in crustal deformation over multi-year scales often exceed the single measurement range of borehole strainmeters. Expanding the measurement range while maintaining high precision is a critical technical challenge. To address this, a full-range measurement system was developed using a bidirectional analog multi-switch based on MOS transistors and automatic feedback control. This system automatically adjusts the zero point of the measurement bridge, maintaining the bridge output at a near-balanced state. The quantifiable zero-setting actions are dynamically converted into equivalent voltage, enabling automatic full-range measurements while fully utilizing the effective linear range of the differential capacitive sensors. A laboratory performance tests demonstrated that an RZB borehole strainmeter equipped with this automatic zero-setting range extension system successfully covers the differential capacitive sensor’s effective linear range of approximately 100 μm.