Michael Watson

Dr. Michael Watson

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2018 in Wear
Verified
Journal Article
Open access
MWMichael Watson
Michael Watson
MMMatthew Marshall
Matthew Marshall

23 December 2014 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MWMichael Watson
Michael Watson
HLH. Long
H. Long
BLB. Lu
B. Lu

23 July 2014 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
NFN Fois
N Fois
MWMichael Watson
Michael Watson
JSJonathan Stringer
Jonathan Stringer
MMMb Marshall
Mb Marshall
Abradable linings are frequently used on the inside of aero-engine casings. During the operation of engine, the rotating blades may strike the lining of the casing. The wear mechanisms present during these incursions have been re-produced on a scaled test rig platform. Previously, characterisation of the wear has been performed using a stroboscopic imaging technique in order to identify the different wear mechanisms at the incursion conditions investigated. In the present study, a dynamometer has been included in the test arrangement allowing the measurement of the contact force. This approach has then been combined with sectioning of the abradable test samples, in order to investigate the material response to the different incursion conditions. The wear results, the cutting force and material structure post-incursion show a high degree of correlation. At low incursion rates, significant consolidation and solidification of abradable material was observed, whilst at the same time adhesive transfer to the blade was recorded along with a low tangential to normal force ratio. At high incursion rates, little solidification and consolidation was observed, together with negligible adhesion and a higher tangential force, suggesting a cutting mechanism. Transitions in material behaviour, wear mechanism, and force ratio were observed at the same incursion condition, further highlighting the link between the different experimental measurements.

1 September 2015 in Wear
Verified
Journal Article
Closed access
MWMichael Watson
Michael Watson
NFN. Fois
N. Fois
MMM.B. Marshall
M.B. Marshall

5 August 2016 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
NFN Fois
N Fois
MWMichael Watson
Michael Watson
MMMb Marshall
Mb Marshall
In aero-engines it is possible for the blades of the compressor, turbine or fan to incur into their casings. At these interfaces a lining of composite abradable material is used to limit damage to components and thereby sustain the efficiency and longevity of the engine as a whole. These composite materials must have good abradability and erosion resistance. Previously, the wear mechanisms at the contact between the blade and the coating have been characterised using stroboscopic imaging and force measurement on a scaled test-rig platform. This work is focused on the characterisation of the wear mechanism for two different hardnesses of abradable lining. The established stroboscopic imaging technique and contact force measurements are combined with sectioning of the abradable material in order to analyse the material’s response during the tests. A measure of the thermal properties and the resulting temperature of the linings during the test have also been made to further understand the effect of coating hardness. The wear mechanism, material response, contact force and thermal properties of the coating have been used to characterise the different material behaviour with different hardness. At low incursion rates, with a soft coating, the blade tip becomes worn after an initial adhesive transfer from the coating. Post-test sectioning showed blade material and significant compaction present in the coating. The harder coating produced adhesion on the blade tip with solidification observed in the coating. Thermal diffusivity measurements and modelling indicated that thermally driven wear observed was as a consequence of the increased number of boundaries between the metal and hBN phases present interrupting heat flow, leading to a concentration of surface heat. At higher incursion rates, the wear mechanism is more similar between the coatings and a cutting mechanism dominates producing negligible adhesion and blade wear.

1 January 2014 in Procedia Engineering
Verified
Journal Article
Open access
MWMichael Watson
Michael Watson
HLHui Long
Hui Long
Wrinkling failure mechanics of conventional metal spinning is investigated by means of finite element (FE) simulation. The results of FE simulation are validated by comparing the modelled roller force with that measured during a spinning experiment. From FE simulation, large residual stresses in the form of bending moments are found to be present in the flange, induced by the roller contact. It is found that wrinkling failure begins when a plastic hinge is formed between the roller and the edge of the blank. These bending moments cause the wrinkled state of the flange to be energetically favourable, which is seen as a reduction in the magnitude of these moments and the elastic strain energy of the FE model at the point of wrinkling