Wenhu Xu

Dr. Wenhu Xu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2023 in Applied Surface Science
Verified
Journal Article
Closed access
MZMufang Zhou
Mufang Zhou
YCYuanyao Cheng
Yuanyao Cheng
MZMin Zhong
Min Zhong
WXWenhu Xu
Wenhu Xu

23 February 2023 in Friction
Verified
Journal Article
Open access
PDF file
MZMufang Zhou
Mufang Zhou
MZMin Zhong
Min Zhong
WXWenhu Xu
Wenhu Xu
Ultrasonic-assisted chemical mechanical polishing (UA-CMP) can greatly improve the sapphire material removal and surface quality, but its polishing mechanism is still unclear. This paper proposed a novel model of material removal rate (MRR) to explore the mechanism of sapphire UA-CMP. It contains two modes, namely two-body wear and abrasive-impact. Furthermore, the atomic force microscopy (AFM) in-situ study, computational fluid dynamics (CFD) simulation, and polishing experiments were conducted to verify the model and reveal the polishing mechanism. In the AFM in-situ studies, the tip scratched the reaction layer on the sapphire surface. The pit with a 0.22 nm depth is the evidence of two-body wear. The CFD simulation showed that abrasives could be driven by the ultrasonic vibration to impact the sapphire surface at high frequencies. The maximum total velocity and the air volume fraction (AVF) in the central area increased from 0.26 to 0.55 m/s and 20% to 49%, respectively, with the rising amplitudes of 1–3 µm. However, the maximum total velocity rose slightly from 0.33 to 0.42 m/s, and the AVF was nearly unchanged under 40–80 r/min. It indicated that the ultrasonic energy has great effects on the abrasive-impact mode. The UA-CMP experimental results exhibited that there was 63.7% improvement in MRR when the polishing velocities rose from 40 to 80 r/min. The roughness of the polished sapphire surface was Ra = 0.07 nm. It identified that the higher speed achieved greater MRR mainly through the two-body wear mode. This study is beneficial to further understanding the UA-CMP mechanism and promoting the development of UA-CMP technology.

10 December 2021 in Mechanics of Advanced Materials and Structures
Verified
Journal Article
Closed access
CSChong Sheng
Chong Sheng
MZMin Zhong
Min Zhong
WXWenhu Xu
Wenhu Xu
Polished sapphire has been widely used because of its superior mechanical and physical characteristics. However, the polishing process of sapphire is still unclear and the processing effects need to be improved. Therefore, the polishing process of sapphire with diamond abrasive particles was studied by molecular dynamics method. The behavior of diamond removing sapphire material in polishing process was researched. The effects of the polishing speed, depth, and the abrasive size were investigated in the aspects of polishing force, surface topography, subsurface damage, removed atoms, temperature distribution and average friction coefficient. The outcomes indicated that the surface temperature of sapphire was higher with the rising polishing velocity, but the subsurface defect of sapphire was deeper. Larger indentation depths resulted in higher forces and temperatures, deeper grooves, more removed atoms and bigger average friction coefficients, but poor polished subsurface. Bigger abrasives gained lower friction coefficients and higher numbers of removed atoms. It was found that both good polishing efficiency and quality are obtained under the speed 150 m/s, the polishing depth 15 Å and the abrasive particle radius 20 Å. This study is helpful to improving the sapphire polishing effects and understanding its polishing process.

4 November 2021 in Mechanics of Advanced Materials and Structures
Verified
Journal Article
Closed access
MZMufang Zhou
Mufang Zhou
MZMin Zhong
Min Zhong
WXWenhu Xu
Wenhu Xu
Sapphire possesses chemically inert and high hardness. Therefore, it is difficult to get idea material removal rate (MRR) and low surface roughness through chemical mechanical polishing (CMP). Ultrasonic vibration assisted chemical mechanical polishing (UV-CMP) can effectively increase the MRR and decrease the roughness of sapphire surface by combining ultrasonic with CMP. In this article, computational fluid dynamics was adopted to research the effects of ultrasonic amplitude on slurry behavior in UV-CMP. The distribution and variations of physical properties such as velocity, pressure, and air volume fraction were characterized at the microscopic level. The importance of cavitation in UV-CMP was discussed. The accuracy of numerical results was verified by the experiments of sapphire UV-CMP. The results show that the amplitude has a vital influence on the polishing effects. The ultrasonic vibration, f = 40 kHz and P = 60 W, can make the MRR and polished surface roughness Ra of sapphire reach 0.96 μm/h and 0.095 nm, respectively. It is much better than 0.66 μm/h and 0.261 nm of sapphire CMP.

28 January 2025 in Precision Engineering
Verified
Journal Article
Closed access
HKHuilong Kang
Huilong Kang
MZMin Zhong
Min Zhong
XLXiaobing Li
Xiaobing Li
MYMeirong Yi
Meirong Yi
JCJianfeng Chen
Jianfeng Chen
WXWenhu Xu
Wenhu Xu

14 September 2024 in Precision Engineering
Verified
Journal Article
Closed access
WXWenhu Xu
Wenhu Xu
CHCheng Huang
Cheng Huang
XLXianghong Liu
Xianghong Liu
MZMin Zhong
Min Zhong
JCJianfeng Chen
Jianfeng Chen
XLXiaobing Li
Xiaobing Li