Saifuddin Aziz

Dr. Saifuddin Aziz

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
SASaifuddin Aziz
Saifuddin Aziz
IAIka Dewi Ana
Ika Dewi Ana
YYYusril Yusuf
Yusril Yusuf
HPHarno Dwi Pranowo
Harno Dwi Pranowo
A carbonate-hydroxyapatite-based antibacterial implant material with low cytotoxicity was synthesized. The silver ion (Ag+) was incorporated into CHA material, resulting in silver-doped carbonate hydroxyapatite (CHA-Ag). The microwave-assisted precipitation method was used to synthesize the CHA-Ag material. The amount of Ag+ was varied at 0.005, 0.010, and 0.015 mol fractions (χAg). The XRD results showed that the diffractograms corresponded with hydroxyapatite (ICSD 98-05-1414), without any additional phase. The presence of carbonate ions was indicated by vibrations at wavenumber of 871, 1411, and 1466 cm−1 in the infrared spectra. The CHA-Ag materials were agglomerates of nanosized particles with low crystallinity. The particle size and crystallinity of the materials decreased due to the incorporation of CO32− and Ag+. The incorporated Ag+ successfully inhibited peri-implant-associated bacterial growth. The antibacterial ability increased alongside the increase in the Ag+ amount. The pre-osteoblast MC3T3E1 cell could grow up to >70% in the MTT assay, despite the use of Ag+ as a dopant. The cell viability was higher in the CHA-Ag-containing media than in the CHA-containing media. The MTT assay also revealed that the CHA-Ag cytotoxicity decreased even though the Ag+ amount increased. The CHA-Ag-15 had the lowest cytotoxicity and highest antibacterial activity. Therefore, the optimal amount of Ag+ in the CHA-Ag formulation was χAg = 0.015.

1 September 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
BPBidhari Pidhatika
Bidhari Pidhatika
DKDeepak Kumar
Deepak Kumar
JLJuntian Liu
Juntian Liu
YSYogi Swasono
Yogi Swasono
RRReza Rudianto
Reza Rudianto
PNPrathima C. Nalam
Prathima C. Nalam
This study investigates the effect of surface functionalization of geosilica nanoparticles incorporated into dental resin composites on their mechanical and tribological performance. Geosilica (GeoSi), derived from Indonesian geothermal sludge, was functionalized with four distinct silane coupling molecules: 3-methoxysilyl propyl methacrylate (MTSPM), octyltrimethoxysilane (OTS), (3-aminopropyl) triethoxysilane (APTES), and bis-[3-(triethoxysilyl)propyl] tetrasulfide (TESPT), and incorporated at 40 wt.% into a bisphenol A-glycidyl methacrylate/triethylene glycol dimethacrylate (BisGMA/TEGDMA) resin matrix. Microhardness of TESPT-functionalized GeoSi-R exhibiting the highest hardness (~25.47 VHN), closely matching the commercial composite, but exceeding unfunctionalized GeoSi-R (~10.06 VHN) and APTES-functionalized GeoSi-R (~18.87 VHN). Tribological tests were conducted against a stainless-steel counterface at varying contact pressures (110 ‐ 400 MPa) and sliding speeds (1 – 5 mm/s) in natural saliva. The measurements revealed a strong correlation between microhardness and the coefficient of friction (COF). GeoSi‐TESPT‐R, the hardest composite, exhibited the highest COF (~0.037) at lower contact pressures (240 MPa), attributed to reduced contact deformation, but showed the largest decrease in COF at higher pressure (~0.012 at 400 MPa) and was the only composite to sustain contact pressures up to 400 MPa without sliding seizure. Under indentical contact pressure, TESPT-R composites exhibited higher specific wear rates than APTES-R composites; however, they showed greater load resistanace, consistent with the formation of a stable protective tribofilm. Overall, these findings demonstrate that tailored silane-mediated interfacial chemistry of GeoSi nanoparticles enhances interfacial bonding and load-bearing capacity, improves wear resistance, and enables pressure-adaptive low-friction performance in dental restorative composites.

28 April 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
FKFrendy Jaya Kusuma
Frendy Jaya Kusuma
SASaifuddin Aziz
Saifuddin Aziz
BPBidhari Pidhatika
Bidhari Pidhatika
INI. Wayan Ngarayana
I. Wayan Ngarayana
AAAnhar Riza Antariksawan
Anhar Riza Antariksawan
The deployment of advanced nuclear energy systems and closed fuel cycles requires improved understanding of actinide materials characteristics under electrochemical processing conditions, i.e., for spent nuclear fuel (SNF) recycling via molten-salt pyroprocessing. Meanwhile, the relationship between oxygen stoichiometry, dopant incorporation, and electronic properties in uranium and mixed-oxide fuels remains insufficiently characterized. This study addresses these challenges by developing machine learning models to predict both formation energies and band gaps of actinide materials. Using data from the Open Quantum Materials Database, this work represents the first application of ML to characterize actinide band gap evolution. The models were developed using Random Forest and Extreme Gradient Boosting (XGB) algorithms, with XGB become the best model (R2 = 0.97 for formation energy and 0.90 for band gap prediction). Feature importance analysis identified electronegativity and Mendeleev number as key descriptors governing thermodynamic stability and electronic band gap. The trained models were then applied to simulate oxygen reduction and dopant incorporation on uranium, plutonium, and mixed-oxide systems, including incorporation of fission products and noble metals, to evaluate their effects on formation energy and band gap evolution. These results demonstrate the capability of machine learning as a computational framework for the preliminary evaluation of SNF processing, providing critical insights into fuel design and electrode selection.