William Smith

William Smith


Research Focus & Metrics

Academic Career Length

35Years (1992-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 March 2010 in Energy Policy
Verified
Journal Article
Closed access
WSWilliam Smith
William Smith

26 February 2021 in Energy & Fuels
Verified
Journal Article
Open access
ATAnna Trubetskaya
Anna Trubetskaya
CLChunshui Lin
Chunshui Lin
AOand Jurgita Ovadnevaite
and Jurgita Ovadnevaite
Darius CeburnisDarius Ceburnis
Darius Ceburnis
COColin O’dOwd
Colin O’dOwd
WSWilliam Smith
William Smith
Solid-fuel stoves are at the heart of many homes not only in developing nations, but also in developed regions where there is significant deployment of such heating appliances. They are often operated inefficiently and in association with high emission fuels like wood. This leads to disproportionate air pollution contributions. Despite the proliferation of these appliances, an understanding of particulate matter (PM) emissions from these sources remains relatively low. Emissions from five solid fuels are quantified using a “conventional” and an Ecodesign stove. PM measurements are obtained using both “hot filter” sampling of the raw flue gas, and sampling of cooled, diluted flue gas using an Aerosol Chemical Speciation Monitor and AE33 aethalometer. PM emissions factors (EF) derived from diluted flue gas incorporate light condensable organic compounds; hence they are generally higher than those obtained with “hot filter” sampling, which do not. Overall, the PM EFs ranged from 0.2 to 108.2 g GJ–1 for solid fuels. The PM EF determined for a solid fuel depends strongly on the measurement method employed and on user behavior, and less strongly on secondary air supply and stove type. Kerosene-based firelighters were found to make a disproportionately high contribution to PM emissions. Organic aerosol dominated PM composition for all fuels, constituting 50–65% of PM from bituminous and low-smoke ovoids, and 85–95% from torrefied olive stone (TOS) briquettes, sod peat, and wood logs. Torrefied biomass and low-smoke ovoids were found to yield the lowest PM emissions. Substituting these fuels for smoky coal, peat, and wood could reduce PM2.5 emissions by approximately 63%.

1 August 2012 in Energy Conversion and Management
Verified
Journal Article
Closed access
RMRonan K. McGovern
Ronan K. McGovern
WSWilliam Smith
William Smith

1 December 2014 in Applied Thermal Engineering
Verified
Journal Article
Closed access
CCCathal T. Ó Cléirigh
Cathal T. Ó Cléirigh
WSWilliam Smith
William Smith

8 April 2013 in SAE International Journal of Engines
Verified
Journal Article
Closed access
PDF file
IWIan Whelan
Ian Whelan
DTDavid Timoney
David Timoney
WSWilliam Smith
William Smith
SSStephen Samuel
Stephen Samuel
This work investigates the effect of a three-way catalytic converter and sampling dilution ratio on nano-scale exhaust particulate matter emissions from a gasoline direct-injection engine during cold-start and warm-up transients. Experimental results are presented from a four cylinder in-line, four stroke, wall-guided direct-injection, turbo-charged and inter-cooled 1.6 litre gasoline engine. A fast-response particulate spectrometer for exhaust nano-particle measurement up to 1000 nm was utilised. It was observed that the three-way catalytic converter had a significant effect on particle number density, reducing the total particle number by up to 65 % over the duration of the cold-start test. The greatest change in particle number density occurred for particles less than 23 nm diameter, with reductions of up to 95 % being observed, whilst the number density for particles above 50 nm diameter exhibited a significant increase. The exhaust temperature plays a significant role on the influence of the catalytic converter on the nano-scale particulate matter. It is evident that the dilution ratio of the exhaust sample has a distinct effect on the particulate matter number and size distribution, influencing the engine-out PM more significantly than the tailpipe-out PM during cold-start engine operation. The catalytic converter also has a considerable effect on the estimated total particle mass.