Uplift-restricted and slip-permitted (URSP) connectors have been demonstrated to effectively enhance the anti-cracking performance of RC slabs in negative moment areas. While their efficacy is recognized, studies of composite frames utilizing URSP connectors remain scarce, limiting their application in construction. This research undertakes a numerical analysis of the seismic performance of steel–concrete composite frames that employ URSP connectors. The influence of key design parameters on seismic behavior is scrutinized. Leveraging prior tests on composite frames with URSP connectors carried out by the authors’ group, a sophisticated three-dimensional FEM model is crafted. This model, built using the ABAQUS software (2016), accounts for the intricate mechanical behaviors of shear connectors. The fidelity of the FEM model is validated through a juxtaposition of numerical and test outcomes, assessing strain distribution, damage patterns, and load–displacement curves. This numerical model serves as a basis for the study, exploring the impacts of three crucial design parameters on structural seismic performance. The findings suggest that the arrangement length of URSP connectors should be constrained to less than half of the frame beam’s span to optimize mechanical performance during seismic events. Additionally, enhancing both the flange thickness and the steel beam’s height is recommended to further bolster structural integrity.

The uplift-restricted and slip-permitted (URSP) connector is a new type of connector used in steel–concrete composite structures that has been proven to improve the structural performance of negative moment regions. Since this connector changes the interface restraint between the slab and steel beam, there is an imperative to study the seismic performance of steel–concrete composite frame systems with this new type of connector. In this study, the dynamic behavior of composite frame structures with URSP connectors under seismic loads was numerically investigated. First, a beam–shell mixed model was used and complex interfaces of different connectors were considered while establishing a numerical model to conduct elasto–plastic time history analysis under various seismic loads. This numerical model was validated with the frame sub-assemblage experimental results of quasi-static cyclic tests. Second, the model analysis results of structures with URSP connectors were obtained and compared with those of traditional structures. Third, dynamic response results including roof displacement, inter-story displacement, and the distribution and failure modes of plastic hinges were analyzed and compared. The comparisons indicated that the arrangement of full-span URSP connectors had a non-negligible influence on the dynamic behavior of the systems. The arrangement increased the maximum inter-story displacement by 31.5% and induced adverse effects in certain cases, which is not suggested in the application of URSP connectors. The partial arrangement of URSP connectors had little influence on the dynamic behavior of the systems, and the frame systems still showed a good seismic performance, which was the same as the traditional composite structural system. These findings may promote the application of URSP connectors in composite structures.

The long-term flexural performance of steel-concrete composite beams after creep is influenced by multiple factors such as the degree of shear connection, cross-sectional form, and boundary conditions. The engineering community has an ambiguous understanding of the coupling effects of these factors. To address this issue, this paper conducts systematic experimental research: six simply supported beams (three box-shaped, three I-shaped) and four continuous beams (two box-shaped, two I-shaped) were designed with three degrees of shear connection (0.57, 1.08, 1.53). These beams first underwent simulated creep tests (24 °C, 80% relative humidity, 10 kN load, 180 days), followed by monotonic bending tests. The results indicate: (1) A high degree of shear connection (1.53) reduces creep deflection by 15–20% compared to partial connection (0.57) and delays the initiation of interface slip to 30% of the ultimate load; (2) Box sections exhibit 10–15% lower creep deflection than I-sections, though both experience 40–60% stiffness reduction after creep; (3) Continuous beams show a 25% improvement in crack resistance in the negative moment region and a 50% increase in flexural capacity at mid-span compared to simply supported beams; (4) After creep, the elastic modulus of concrete decreases by 40–60% (inversely related to the degree of shear connection), with fully connected specimens retaining 55–61% of their strength, while partially connected specimens retain only 43–49%. This study quantifies the degradation patterns of concrete performance, clarifies the influence mechanisms of key structural factors, and provides theoretical and experimental support for the long-term performance design of composite beams. Shear connection design is crucial for mitigating creep effects.