This paper presents a new method of combining Minimum Quantity Lubricant (MQL) with ultrasonic assistance in deep hole drilling processes for difficult-to-cut materials, using internal coolant tools. A small amount of lubricant as 90 mL/h was provided directly into the cutting zone during deep drilling under ultrasonic vibrations exerted on the tool. A comparative experimental study was implemented for two types of drilling processes: conventional drilling (CD) and ultrasonic-assisted drilling (UAD). For each set, three different methods of lubricant feeding methods were applied, including flooding, MQL, and MQL with graphene nanoparticles. A continuous drilling process using a through-hole drill bit (D = 5 mm, L = 8D) for AISI SUS 304 stainless steel was implemented to validate the effectiveness of the proposed approach. The results show that the approach proposed can overcome the bottleneck in deep drilling using MQL, providing a higher production rate, longer tool life, and better machining performance in terms of cutting forces and processing ability. Using the newly proposed method, continuous drilling can be done in critical machining conditions, which are typically recommended by the tool manufacturers. The results are promising to expand to deep hole drilling of other hard-to-cut materials.
Agricultural residues are the most abundant biomass and forage resources. Chopping is a precondition for either use, and reducing the shearing force has been considered as one of the most effective way to save energy. A smaller force can also permit more compact mechanical parts of chopping devices. In several cases, power consumption may be large, even when the shearing force is small, if the corresponding cutting velocity is high. Consequently, it is important to minimize both cutting force and power consumption simultaneously. This paper presents a practical approach to solve the multi-objective optimization problem for chopping processes of corn stalks. Applying the Taguchi design of experiments, a plan of 27 chopping tests was conducted. Based on the grey relational grade analysis and analysis of variance technique, optimum levels as well as the percentage contribution of such parameters were identified. Experimental results showed that the multi-response optimization problem in chopping corn stalks can be effectively addressed through the combination of Taguchi design and grey relational analysis. The results can be expanded for practical applications in design and operation of chopping machines for agricultural residues.
20 September 2024 in Journal of Sound and Vibration
In this paper, the influence of ultrasonic vibration on the forming forces and surface quality of products formed using an ultrasonic-assisted incremental sheet forming (UISF) method was investigated and compared with an incremental sheet forming (ISF) method. The elements and parameters used for research include a sheet of Al 5052 aluminum alloy with thickness of 1.0 mm, a lathe with a feed rate of 70–130–225 rpm, and step size of 1.0–1.5–2.0 mm. The results show that ultrasonic vibration significantly reduces the forming forces, of which the main forming force Fzmax is reduced by about 20%. Besides, the results also show that the surface quality of products formed via UISF is significantly improved compared to that formed by ISF.
Implementing the ultrasonic vibration-assisted incremental sheet-forming (UISF) process has been proven to significantly reduce the forming force, improve the surface quality, and enhance the accuracy of the sheet-forming process. However, such effectiveness has primarily focused on easily deformable materials (such as AA1050 and AA1060 aluminum alloys) and small step-down sizes (from 0.3 mm to 0.5 mm). To further enhance the process, it is crucial to study larger step-down sizes and harder materials. In this study, a series of UISF experiments were conducted, with step-down sizes ranging from 0.5 mm to 1.5 mm and feed rates ranging from 200 mm/min to 1200 mm/min. The influence of ultrasonic vibration on the effectiveness of force reduction and the optimal operation parameters was experimentally tested. Forming aluminum alloy AA5052, a difficult-to-deform material with two thicknesses of 0.5 mm and 1.0 mm, indicates that the axial force Fz and the tool movement resistance force Fy tend to decrease significantly with ultrasonic vibration assistance. Optimal equations for force reduction Fz and Fy have been developed for plate thickness based on the step-down size and feed rate. The optimal results show that for 1.0 mm thickness, reductions in Fz and Fy can reach 58.73% and 69.17%, respectively, and that of 64.17% and 71.98%, respectively, for 0.5 mm thickness.