Tianyong Jiang

Dr. Tianyong Jiang

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 November 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Linsheng HuoLinsheng Huo
Linsheng Huo
CLChuanbo Li
Chuanbo Li
TJTianyong Jiang
Tianyong Jiang
Hong-Nan LiHong-Nan Li
Hong-Nan Li
Steel bars, which are commonly used as reinforcements in concrete structures, are slender rods and are good conduits for stress wave propagation. In this paper, a lead zirconate titanate (PZT)-based steel bar corrosion monitoring approach was proposed. Two PZT transducers are surface-bonded on the two ends of a steel rod, respectively. One works as actuator to generate stress waves, and the other functions as a sensor to detect the propagated stress waves. Time reverse technology was applied in this research to monitor the corrosion of the steel bars with a high signal to noise ratio (SNR). Accelerated corrosion experiments of steel bars were conducted. The anti-corrosion performance of the protected piezoceramic transducers was tested first, and then they were used to monitor the corrosion of the steel bar using the time reversal method. The degree of corrosion in the steel bar was determined by the ratio of mass loss during the experiment. The experimental results show that the peak values of the signal that were obtained by time reversal operation are linearly related to the degree of corrosion of the steel bar, which demonstrates the feasibility of the proposed approach for monitoring the corrosion of steel bars using the time reversal method enabled by piezoceramic transducers.

15 November 2018 in Sensors
Verified
Journal Article
Open access
PDF file
TJTianyong Jiang
Tianyong Jiang
YZYaowen Zhang
Yaowen Zhang
LWLei Wang
Lei Wang
LZLiang Zhang
Liang Zhang
Gangbing SongGangbing Song
Gangbing Song
Modular bridge expansion joints (MBEJs) are commonly used in bridges and are often subjected to fatigue damages, which necessitate fatigue monitoring of MBEJs to ensure the reliable operation of the bridges. In this paper, a stress wave based active sensing approach using piezoceramic transducers is developed to monitor the fatigue damage of MBEJ. A MBEJ involves mainly center beam, edge beam, support bar, support box, sliding bearing, sliding spring, elastomeric strip seal, full-penetration weld and reinforcing plate. In practice, for a MBEJ, the part that is most prone to fatigue damage is the full-penetration weld between the center beam and the support bar. In this paper, a specimen, which is the full-scale center-beam/support-bar (CB/SB) assembly, was designed and fabricated to facilitate the experimental study. The assembly mainly includes center beam, support bar, reinforcing plate, and full-penetration weld. The lead zirconate titanate (PZT) transducer bonded on the support bar was used as the actuator and the PZT transducer mounted on the center beam was as the sensor. Dial indicators were utilized to measure the vertical displacement of the center beam. Two series of tests, including static test, and fatigue test, were performed on the specimen in an alternating fashion. Based on the number of cyclic loading, the experiment was divided into six different stages: 0th cycle (the healthy state), 0.8 million cycles, 1.6 million cycles, 2.4 million cycles, 3.2 million cycles, and 4 million cycles. The signals received by the PZT sensor were analyzed with the help of wavelet packet analysis. In addition, the structure stiffness also was considered as a comparative approach in this paper. Experimental results show that during the fatigue test, the structure stiffness decreases with the number of cycle loading. However, the method can only obtain the fatigue damage impact on the entire structure, and cannot determine the fatigue damage degree of a certain weld. On the other hand, the proposed method can accurately monitor the fatigue damage degree of full-penetration welds. The research results show that the developed piezoceramic enabled active sensing approach can monitor and estimate the fatigue damage in MBEJ in real-time.

27 April 2019 in Sensors
Verified
Journal Article
Open access
PDF file
TJTianyong Jiang
Tianyong Jiang
YHYue Hong
Yue Hong
JZJunbo Zheng
Junbo Zheng
LWLei Wang
Lei Wang
HGHaichang Gu
Haichang Gu
In this paper, the authors present a stress wave-based active sensing method to detect the crack in FRP-reinforced concrete beams. The embedded smart aggregates (SAs), which utilize Lead Zirconate Titanate (PZT) as transducers, are employed in this research to generate and sense the stress wave. Three specimens are involved in the experimental program and each is made of concrete, longitudinal distributed reinforcement, steel stirrups, main bar (FRP bar or steel bar), and four SAs. A pair of SAs installed on the lower part of the main bar and the other pair of SAs mounted on the upper part of main bar are utilized to monitor the crack occurrence and development in the three test specimens. The signals received by the SA sensors are analyzed in both time domain and frequency domain. The wavelet packet energy is used to extract damage features. The applied load–vertical displacement curves of mid-span in the specimen are obtained. Experimental results show the test specimens experience crushing failure when the concrete compression exceeds its compressive strength. Increasing the contact area between FRP bar and concrete can effectively improve the cracking load of the FRP-reinforced concrete beam and reduce the cracking speed and depth of FRP-reinforced concrete beam; on the other hand, increasing the elastic modulus of the main bar can slow down the crack development of concrete on the upper side of the main bar and decrease the displacement of reinforced concrete beam during the loading test process. The research results show that the developed piezoceramic-based active sensing method, though low-cost, can monitor the crack-induced damage and estimate the process of damage degree in real-time, and has potentials to provide an early warning of crack occurrence and development for FRP-reinforced concrete beams.

29 September 2017 in Sensors
Verified
Journal Article
Open access
PDF file
TJTianyong Jiang
Tianyong Jiang
JZJunbo Zheng
Junbo Zheng
Linsheng HuoLinsheng Huo
Linsheng Huo
Gangbing SongGangbing Song
Gangbing Song
With the development of the post-tensioning technique, prestressed concrete structures have been widely used in civil engineering. To ensure the long-term effectiveness of the prestressed tendon, the grouting quality of the tendon duct is one of the important factors. However, it is still a challenge to monitor the grouting quality of post-tensioning tendon ducts, due to the invisibility of the grouting. The authors’ previous work proposed a real-time method that employed a stress wave-based active sensing approach with piezoceramic transducers to monitor the grouting compactness of a Post-Tensioning Tendon Duct (PTTD). To further understand the piezoceramic induced stress wave propagation in the PTTD with different grouting levels, this paper develops a two-dimensional finite element model for monitoring the grouting compactness of the tendon duct with a piezoceramic transducer. A smart aggregate (SA) developed to utilize one Lead Zirconate Titanate (PZT) transducer with marble protection is installed in the center location of the tendon duct as an actuator. Two PZT patches are bonded on the bottom and top surface of the tendon duct as the sensors. The analysis results show that the finite element analysis results are in good agreement with the experimental results, which demonstrates that the finite element analysis is feasible and reliable. For the top half of the specimen, not much stress wave could be detected before the full grouting level, except for negligible signals that may propagate through the walls of the tendon duct. When the tendon duct grouting is at 100%, the stress wave propagates to the top of the specimen, and the displacements are symmetric in both left-right and top-bottom directions before the stress waves reach the boundary. The proposed two-dimensional finite element model has the potential to be implemented to simulate the stress wave propagation principle for monitoring grouting compaction of the post-tensioning tendon duct.

22 February 2020 in Sensors
Verified
Journal Article
Open access
PDF file
TJTianyong Jiang
Tianyong Jiang
BHBin He
Bin He
YZYaowen Zhang
Yaowen Zhang
LWLei Wang
Lei Wang
To understand the characteristics of longitudinal grouting quality, this paper developed a stress wave-based active sensing method using piezoceramic transducers to detect longitudinal grouting quality of the prestressed curved tendon ducts. There were four lead zirconate titanate (PZT) transducers installed in the same longitudinal plane. One of them, mounted on the bottom of the curved tendon duct, was called as an actuator for generating stress waves. The other three, pasted on the top of the curved tendon duct, were called as sensors for detecting the wave responses. The experimental process was divided into five states during the grouting, which included 0%, 50%, 75%, 90%, and 100% grouting. The voltage signals, power spectral density (PSD) energy and wavelet packet energy were adopted in this research. Experimental results showed that all the amplitudes of the above analysis indicators were small before the grouting reached 90%. Only when the grouting degree reached the 100% grouting, these parameters increased significantly. The results of different longitudinal PZT sensors were mainly determined by the distance from the generator, the position of grouting holes, and the fluidity of grouting materials. These results showed the longitudinal grouting quality can be effectively evaluated by analyzing the difference between the signals received by the PZT transducers in the curved tendon duct. The devised method has certain application value in detecting the longitudinal grouting quality of prestressed curved tendon duct.

1 November 2019 in Journal of Central South University
Verified
Journal Article
Closed access
PDF file
ZTZhong-Chu Tian
Zhong-Chu Tian
WPWen-Ping Peng
Wen-Ping Peng
JZJian-Ren Zhang
Jian-Ren Zhang
TJTianyong Jiang
Tianyong Jiang
YDYang Deng
Yang Deng