Powder bed fusion of metals using a laser beam (PBF-LB/M) is a process that enables the fabrication of geometrically complex parts. In this process, a laser beam melts a metallic powder locally to build the desired geometry. The melt pool solidifies rapidly, which results in high cooling rates. These rates vary during the process in line with the geometric characteristics of the part, which leads to a non-uniform microstructure along with anisotropic mechanical properties. The unknown part characteristics prevent the process from being used in safety-critical applications. Thermographic in situ process monitoring provides information about the thermal field, enabling predictions of the resulting material properties. This study presents a novel methodology for the thermographic measurement of cooling rates during the PBF-LB/M process using a high-speed thermographic camera. The cooling rates occurring during the manufacturing of 316L tower-like specimens were measured. The cooling rate decreased with increasing build height, due to the heat accumulation in the parts. The microhardness profile of the parts was tested perpendicularly and parallel to the build direction. A significant decrease in hardness values was observed along the build height. The measured cooling rate was correlated to the microhardness profile of the specimens using a Hall–Petch type relationship. The results show a high level of reproducibility of the cooling rates between different specimens in the same build job as well as between subsequent build jobs. The presented methodology allows studying the effects of the geometry on the cooling rates and the resulting mechanical properties of 316L specimens.

Conventional manufacturing technologies, such as milling or casting, are limited in terms of the manufacturable complexity of the parts to be produced. They are also restricted in terms of the local modifiability of the mechanical properties. Additive manufacturing, specifically the Powder Bed Fusion of Metals using a Laser Beam (PBF-LB/M), is a novel method, which is capable of addressing both limitations. However, the resulting parts are often prone to cracking during PBF-LB/M and in the service afterward because of high thermally induced local stress intensities. Selectively modifying the process parameters during the fabrication can be a suitable strategy to locally reduce the failure susceptibility. Over the course of this study, samples made from the nickel-based superalloy Inconel 718 were manufactured with varying laser powers, hatch distances, and scan speeds. The samples were divided into stress crack specimens as well as static and dynamic tensile test specimens. The grain structure was investigated, and correlations between the microstructure and the cracking susceptibility were determined. It was found out that variations in the laser power had the most pronounced effect on the grain structure and the failure behavior. An increasing grain size enhanced the fracture resistance in the stress crack samples while the static and dynamic mechanical properties deteriorated. Based on these results, the application area of PBF-LB/M could potentially be widened due to the manufacturability of parts otherwise susceptible to stress-induced cracking. The mechanical properties of as-built parts can remain unchanged utilizing a local process parameter adaption.

The potential of an optimization process with respect to reduced mass can be used to the full extent by utilizing a high-strength material as it is, among others, strength-dependent. For the additive manufacturing process, Powder Bed Fusion of Metals using a Laser Beam (PBF-LB/M), 316L is commonly used. PBF-LB/M/316L has its benefits, like good material properties, such as availability, corrosion resistance, strength, and ductility. Nevertheless, a higher-strength material is required to fully take advantage of the optimization process and achieve a greater reduction in the mass of manufactured parts. The high-strength austenitic stainless steel investigated in this study is Printdur^® HSA. Its main alloying elements are manganese, chromium, molybdenum, carbon, and nitrogen. The steel obtains its high strength properties from the alloyed carbon and nitrogen via solid solution hardening and improving the austenite stability. Therefore, it is defined as (C+N) steel. The datasheet of the powder manufacturer describes a yield strength (R_p0.2; 0.2% offset proof stress) of 915 MPa, an ultimate tensile strength of 1120 MPa, and an elongation at fracture of 30%. These are clear benefits in comparison to PBF-LB/M/316L. Since there are no further investigations made on Printdur^® HSA, a thorough investigation of material behavior, fatigue life, and microstructure is needed.