This paper introduces a search-and-rescue robot system used for remote sensing of the underground coal mine environment, which is composed of an operating control unit and two mobile robots with explosion-proof and waterproof function. This robot system is designed to observe and collect information of the coal mine environment through remote control. Thus, this system can be regarded as a multifunction sensor, which realizes remote sensing. When the robot system detects danger, it will send out signals to warn rescuers to keep away. The robot consists of two gas sensors, two cameras, a two-way audio, a 1 km-long fiber-optic cable for communication and a mechanical explosion-proof manipulator. Especially, the manipulator is a novel explosion-proof manipulator for cleaning obstacles, which has 3-degree-of-freedom, but is driven by two motors. Furthermore, the two robots can communicate in series for 2 km with the operating control unit. The development of the robot system may provide a reference for developing future search-and-rescue systems.
Formation control is an important problem in cooperative robotics due to its broad applications. To address this problem, the concept of a virtual linkage is introduced. Using this idea, a group of robots is designed and controlled to behave as particles embedded in a mechanical linkage instead of as a single rigid body as with the virtual structure approach. As compared to the virtual structure approach, the method proposed here can reconfigure the group of robots into different formation patterns by coordinating the joint angles in the corresponding mechanical linkage. Meanwhile, there is no need to transmit all the robots’ state information to a single location and implement all of the computation on it, due to virtual linkage’s hierarchical architecture. Finally, the effectiveness of the proposed method is demonstrated using two simulations with nine robots: moving around a circle in line formation, and moving through a gallery with varying formation patterns.
This paper presents a novel sensing mode for using mobile robots to collect disaster ground information when the ground traffic from the rescue center to disaster site is disrupted. Traditional sensing modes which use aerial robots or ground robots independently either have limited ability to access disaster site or are only able to provide a bird’s eye view of the disaster site. To illustrate the proposed sensing mode, the authors have developed a Multi-robot System with Air Dispersal Mode (MSADM) by combining the unimpeded path of aerial robots with the detailed view of ground robots. In the MSADM, an airplane carries some minimal reconnaissance ground robots to overcome the paralyzed traffic problem and deploys them on the ground to collect detailed scene information using parachutes and separation device modules. In addition, the airplane cruises in the sky and relays the control and reported information between the ground robots and the human operator. This means that the proposed sensing mode is able to provide more reliable communication performance when there are obstacles between the human operators and the ground robots. Additionally, the proposed sensing mode can easily make use of different kinds of ground robots, as long as they have a compatible interface with the separation device. Finally, an experimental demonstration of the MSADM is presented to show the effectiveness of the proposed sensing mode.
With the increase of accidents and disasters occurring in the explosive environment, search-and-rescue activities are more and more essential. At present, explosive-proof robots can be designed for detection in the explosive environment. However, most robots only detect parameters of disaster scenes, and cannot go forward when they are blocked by obstacles. So, manipulators are needed in order for robots to finish search-and-rescue missions. However, few robots can meet these requirements, because it is difficult to design an explosive-proof manipulator. This paper introduces a method used for designing manipulators which can work in the explosive environment. The manipulator adopted in this design method can drive more than three joints, and only uses two motors. One motor is used to supply power for driving joints and the other is used for switching the power among joints. Both of them can be separated with a manipulator and mounted on a robot chassis with an explosive-proof box. In this way, the load capacity and explosion-proof security of manipulators can be improved. The development of this design method can provide a reference for designers to develop future search-and-rescue robots in explosive environments.
The map building is the prerequisite in the mobile robots' autonomous operation in an unknown environment. Most current mobile robots mainly use the 2D map, and the others which use the 3D map have some shortcomings such as the complex data processing algorithm, large computation and time-consuming and so on. The paper presents a 3D data scanning system that combined with the 2D laser radar and the precise rotation head to capture the information of the unknown environment, and building a coordinate system model for calculating the transform matrixes of each coordinate system. Then the pose of the robot got by the odometer and electronic compass, the improved ICP algorithm and the transform matrixes are combined to process the environment information for getting the 3D point cloud, finally the 3D point cloud is displayed on the OpenGL. At last, the experiment about the 3D map building is gone on in the laboratory corridor and the indoor environment. The experimental results show that this 3D data scanning system has higher efficiency and accuracy, and can better reflect the real situation of the environment.