William Gustavo Diaz

Prof. William Gustavo Diaz


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 October 2025 in Processes
Verified
Journal Article
Open access
PDF file
FTFernando Toapanta-Ramos
Fernando Toapanta-Ramos
MRMayra Guashco Rubio
Mayra Guashco Rubio
Fernando Ortega-LozaFernando Ortega-Loza
Fernando Ortega-Loza
WDWilliam Gustavo Diaz
William Gustavo Diaz
A 3D numerical study using computational fluid dynamics simulations is carried out on a heat sink with circular fins. These devices are used to reject heat on motherboards and graphics cards. The software used in this investigation was ANSYS Fluent-CFD, with energy- and momentum-conservation models, as well as two-equation κ−ϵ turbulence models. Three temperatures are set at the base of the heat sink: 80 °C, 90 °C, and 100 °C; as well as three air velocities for cooling: 10 m/s, 15 m/s, and 20 m/s. The analysis determined that the temperature at the fins depends on the length of time the heat sink is exposed to high temperatures. Furthermore, the temperature in the center of the heat sink is lower than at the edges. On the other hand, the analysis times with periods of 2 s, 5 s, and 10 s, this variable being the most fluctuating since significant changes in the temperature of the fins and the surrounding air are observed; increases are determined ranging from 7.96% for the shortest time of exposure to forced convective air, up to 54.55%, for the longest heat-transfer time. However, in the simulations it was observed that from the eighth second the heat transfer stabilizes.

1 April 2025 in Enfoque UTE
Verified
Journal Article
Open access
PDF file
FTFernando Toapanta-Ramos
Fernando Toapanta-Ramos
JEJavier Espin
Javier Espin
WDWilliam Gustavo Diaz
William Gustavo Diaz
In the present study, a numerical investigation is carried out using ANSYS CFD to observe the heat transfer and heat dissipation, the method is by forced convection heat transfer, with a modern and innovative heat sink. In the study, a configuration of six vertical central fins of equal size and three small fins horizontally is observed. With the lower surface heated, this simulates the heat rejection of electronic devices such as video cards in CPUs. The Navier-Stokes equations for fluid dynamics and the Kappa-Epsilon turbulence model based on RNG (Renormalization) are established for this study. The temperature in the air surrounding the heat sink increases by 0.62 to 0.79 °C, for the base temperature of 80 °C and 100 °C, respectively. This means that at a higher air flow speed, 20 m/s, the air has the capacity to heat up more since its heat exchange is stronger, therefore, the heat sink reduces its temperature. heated, this simulates the heat rejection of electronic devices such as video cards in CPUs. The Navier-Stokes equations forfluid dynamics and the Kappa-Epsilon turbulence model based on RNG (Renormalization) are established for this study. Thetemperature in the air surrounding the heat sink increases by 0.62 to 0.79 °C, for the base temperature of 80°C and 100°C, respectively. This means that at a higher air flow speed, 20 m/s, the air has the capacity to heat up more since its heat exchange is stronger, therefore, the heat sink reduces its temperature.

29 June 2026 in Energies
Verified
Journal Article
Open access
PDF file
FTFernando Toapanta-Ramos
Fernando Toapanta-Ramos
Fernando Ortega-LozaFernando Ortega-Loza
Fernando Ortega-Loza
JEJosé Erazo
José Erazo
WDWilliam Gustavo Diaz
William Gustavo Diaz
The increasing power density of modern electronics demands more efficient thermal management. Heat sinks with sinusoidal fins remain understudied, and the combined effect of perforations and variable fin spacing on transient performance has not been systematically quantified. This numerical study, conducted using ANSYS Fluent 2025 R2, analyzes three sinusoidal fin configurations under forced convection (3–5 m/s): solid fins (Case A), perforated fins (Case B), and perforated fins with alternating spacing of 2 mm and 4.5 mm (Case C). The base was maintained at 60 °C during a 20 s transient period. A mesh with an average skewness of less than 0.25 ensured numerical convergence. Case B showed remarkable uniformity in the base temperature (variations < 1 °C), in contrast to Case A (variations of up to 14.17 °C), due to a thermal boundary layer restart effect induced by the perforations. Case C reached the highest heat dissipation temperatures (up to 54.64 °C at 3 m/s), representing a 47.2% increase compared to Case A, indicating more effective heat extraction with this type of separate fin. The critical transient window occurs within the first 5 s (>85% of the total temperature rise). A vertical temperature gradient of 1.19 °C/mm was observed near the base. Although the perforations reduced the heat transfer area by 5.94%, the induced turbulence compensated for this loss. Sinusoidal fins with perforations and variable spacing significantly improve convective heat removal.