Xiao Zhiyu

Prof. Xiao Zhiyu


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2017 in Materials
Verified
Journal Article
Open access
PDF file
ZWZhen Wang
Zhen Wang
XZXiao Zhiyu
Xiao Zhiyu
CHChuanshou Huang
Chuanshou Huang
LWLiping Wen
Liping Wen
WZWeiwen Zhang
Weiwen Zhang
The present article studied the effect of ultrasonic surface rolling process (USRP) on the microstructure and wear behavior of a selective laser melted Ti-6Al-4V alloy. Surface characteristics were investigated using optical microscope, nano-indentation, scanning electron microscope, transmission electron microscope and laser scanning confocal microscope. Results indicated that the thickness of pore-free surfaces increased to 100~200 μm with the increasing ultrasonic surface rolling numbers. Severe work hardening occurred in the densified layer, resulting in the formation of refined grains, dislocation walls and deformation twins. After 1000 N 6 passes, about 15.5% and 14.1% increment in surficial Nano-hardness and Vickers-hardness was obtained, respectively. The hardness decreased gradually from the top surface to the substrate. Wear tests revealed that the friction coefficient declined from 0.74 (polished surface) to 0.64 (USRP treated surface) and the wear volume reduced from 0.205 mm−3 to 0.195 mm−3. The difference in wear volume between USRP treated and polished samples increased with sliding time. The enhanced wear resistance was concluded to be associated with the improvement of hardness and shear resistance and also the inhibition of delamination initiation.

1 May 2009 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
XZXiao Zhiyu
Xiao Zhiyu
MKM.Y. Ke
M.Y. Ke
LFL. Fang
L. Fang
MSM. Shao
M. Shao
YLY.Y. Li
Y.Y. Li

4 March 2020 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
ZLZhongqiang Liu
Zhongqiang Liu
ZWZhen Wang
Zhen Wang
CGChaofeng Gao
Chaofeng Gao
RLRuiping Liu
Ruiping Liu
XZXiao Zhiyu
Xiao Zhiyu

4 March 2016 in Materials
Verified
Journal Article
Open access
PDF file
BYBibo Yao
Bibo Yao
ZZZhaoyao Zhou
Zhaoyao Zhou
LDLiuyang Duan
Liuyang Duan
XZXiao Zhiyu
Xiao Zhiyu
Powder metallurgy (P/M) technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

19 October 2016 in Powder Metallurgy
Verified
Journal Article
Closed access
XLX. Liu
X. Liu
XZXiao Zhiyu
Xiao Zhiyu
HGH.-J. Guan
H.-J. Guan
WZW. Zhang
W. Zhang
FLF.-L. Li
F.-L. Li
Surface rolling was employed to fabricate a densified layer on a powder metallurgy (PM) Fe–2Cu–0.6C piece. A densified surface layer with a depth of 335 μm and a surface hardness of 330 HV0.1 was obtained, in which the lamellar spacing of pearlite and grain size of ferrite were refined. Friction and wear behaviours of the surface densified material were studied. Results indicated that friction coefficient of the rolled material decreased as the load increased, which was lower than that of the un-rolled material. Wear volumes were lower than that of the un-rolled material, which increased as the load increased. Wear loss was caused by flake spalling and grooves, and the wear mechanism mainly was abrasive wear. The surface densified layer with higher hardness and lower porosity can hinder the cracks initiation and propagation on the surface and under the surface, which enhance the wear resistance of the PM material.

27 August 2015 in Materials
Verified
Journal Article
Open access
PDF file
FWFei Wu
Fei Wu
ZZZhaoyao Zhou
Zhaoyao Zhou
LDLiuyang Duan
Liuyang Duan
XZXiao Zhiyu
Xiao Zhiyu
A self-developed rotary multi-cutter device cuts stainless steel wire ropes into segments to fabricate twisted wires. Stainless steel porous twisted wire materials (PTWMs) with a spatial composite intertexture structure are produced by the compaction and subsequent vacuum solid-phase sintering of twisted wires. The stainless steel PTWMs show two types of typical uniaxial tensile failure modes, i.e., a 45° angle fracture mode and an auxetic failure mode (the PTWMs expand along the direction perpendicular to the tension). The effects of the sintering parameters, porosities, wire diameters, and sampling direction on the tensile properties of the PTWMs are carefully investigated. By increasing the sintering temperature from 1130 °C to 1330 °C, the tensile strength of the PTWMs with 70% target porosity increased from 7.7 MPa to 28.6 MPa and the total failure goes down to 50%. When increasing the sintering time from 90 min to 150 min, the tensile strength increases from 12.4 MPa to 19.1 MPa and the total failure elongation drops to 78.6%. The tensile strength of the PTWMs increases from 28.9 MPa to 112.7 MPa with decreasing porosity from 69.5% to 46.0%, and the total failure elongation also increases from 14.8% to 40.7%. The tensile strength and the failure strain of the PTWMs with fine wires are higher than those of the PTWMs with coarse wires under the same porosity. Sampling direction has a small influence on the tensile properties of the PTWMs.