Often overlooked, vibration transmission through the entire body of an animal is an important factor in understanding vibration sensing in animals. To investigate the role of dynamic properties and vibration transmission through the body, we used a modal test and lumped parameter modelling for a spider. The modal test used laser vibrometry data on a tarantula, and revealed five modes of the spider in the frequency range of 20–200 Hz. Our developed and calibrated model took into account the bounce, pitch and roll of the spider body and bounce of all the eight legs. We then performed a parametric study using this calibrated model, varying factors such as mass, inertia, leg stiffness, damping, angle and span to study what effect they had on vibration transmission. The results support that some biomechanical parameters can act as physical constraints on vibration sensing. But also, that the spider may actively control some biomechanical parameters to change the signal intensity it can sense. Furthermore, our analysis shows that the parameter changes in front and back legs have a greater influence on whole system dynamics, so may be of particular importance for active control mechanisms to facilitate biological sensing functions.
31 August 2024 in Journal of Fluids and Structures
As a continuous and smooth morphing concept for aerofoils, the Fish Bone Active Camber (FishBAC) concept has demonstrated significant aerodynamic efficiency improvements over traditional hinged flaps. In this paper, to investigate the static and dynamic aeroelasticity of FishBAC aerofoils, an unsteady two dimensional coupled fluid-structure interaction model is developed, which includes the structural response of the FishBAC spine, skin, stringers, tendons and actuator, coupled to an unsteady aerodynamics model. The structural dynamic model is Timoshenko beam-theory-based, while the aerodynamic model is based on Peters’ unsteady model. The static and dynamic aeroelasticity is studied after the model is validated. Results show that the increase in pulley rotational angle reduces the zero-lift angle of attack, while keeping the slope between the lift coefficient and angle of attack the same. A shorter morphing region closer to the trailing edge is beneficial for generating larger lift coefficient with the same tendon moment and angle of attack. Flutter occurs with the increase of the air speed. When the morphing end position is fixed at 0.9 chord, increasing the morphing length reduces the critical flutter speed significantly, with the second bending mode tending to drive instability. With the same morphing length, moving the morphing region closer to the leading edge increases the critical flutter speed, and the unstable mode changes from the second mode into the first mode.
Magnetorheological dampers (MRD) exhibit strongly nonlinear hysteretic behavior, which poses significant challenges for accurate dynamic modeling and limits the full exploitation of their controllable performance. To address this issue, a physics-informed residual learning framework is proposed for modeling the nonlinear dynamics of MRD. A physics-informed B-spline curve hysteresis (PIBSH) model is first developed to establish a morphology-based white-box parametric formulation, enabling a physically interpretable phenomenological representation of the damping force. The proposed model decomposes the damping force into linear components and a nonlinear hysteretic component described by B-spline functions. By leveraging B-spline basis functions and control points, the model effectively captures the mapping between motion states and local hysteretic characteristics. To further enhance predictive accuracy, a Kolmogorov–Arnold transformer (KAT) is constructed, integrating nonlinear feature extraction capability of the Kolmogorov–Arnold network with the attention-based temporal modeling advantage of the transformer. Based on this structure, a hybrid model termed PIBSH–KAT (PIKAT) is established, where KAT learns and compensates for the residuals between the PIBSH predictions and experimental measurements. Comparative experiments demonstrate that the PIBSH model achieves superior accuracy in representing local hysteretic behavior, while the residual-enhanced PIKAT model further improves prediction precision and generalization performance, achieving a maximum accuracy of 0.9956 under multiple working conditions.
4 June 2026 in Mechanical Systems and Signal Processing
Substrate-borne vibration sensing is an important sensory modality in arthropods, which use externally generated vibration sources to gather information about their environment. Vibrations are subject to mechanical filtering by the legs and body, which implicates a role for morphology in modulating information flow due to the distributed and embedded nature of arthropod mechanosensors. A general problem with sensing is the separation of signal from noise. While internally generated vibrations can be useful for proprioception, they potentially obscure the small displacements generated by substrate vibrations for exteroception. Here, we use a laser vibrometry dataset quantifying the dynamic response of the tarantula Grammostola pulchra to vibrational input at 50 points across its legs and body to examine relative motion in a single axis, enabling us to infer leg biomechanics and test whether these behave rigidly as vibrations are transmitted through the body. We show that the non-rigid legs may dampen large-amplitude motion from cephalothorax/abdomen resonance—increasing signal-to-noise ratio for exteroception at their distal ends. These properties may also act to increase the robustness of vibration sensing to variation in morphological traits affecting the spider’s dynamics. As spider body plans are conserved, we argue the results are generalizable across the mechanosensitive Araneae.
1 March 2026 in Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences
Vibration source localization is an interdisciplinary topic with applications in both engineering and biology. To inspire technologies for use in engineering and understand how spiders may localize a vibration source, we develop a bio-inspired vibration source localization configuration and algorithm. The algorithm first calculates leg inputs using a backward filter forward smoother algorithm with leg responses; it then estimates the source angle, source distance, substrate wave speed and decay rate through optimization, utilizing the time and amplitude relationships between the calculated leg inputs. The algorithm effectiveness is validated through simulations. Results show that the algorithm gives accurate estimation of the source angle and wave speed with varying source distance, source angle, wave speed and decay rate, with errors typically within 3 deg (absolute) and 6% (relative), respectively. The algorithm cannot estimate the source distance. To locate the position, two spider-like agents would be used collaboratively. The algorithm works well even for leg responses with low signal-to-noise ratio. Results also show that the four-leg combination which includes front and back two legs is the minimum leg requirement. Increasing the leg–substrate contact damping can improve the algorithm accuracy. These results also give us new insights into how spiders may localize a vibration source.