Chemical flooding, such as alkaline-surfactant (AS) or nanoparticles-surfactant (NS) flooding, is an enhanced oil recovery (EOR) technique that has been increasingly utilized to enhance the oil production rate and recovery factor while reducing chemical adsorption. The AS/NS flooding process involves the injection of a mixture of surfactant and alkali/nanoparticles solutions into an oil reservoir to reduce the interfacial tension between the oil and water phases by surfactant and lower surfactant adsorption by alkali or nanoparticles (NPs) to improve the residual oil recovery. In this study, the AS/NS flooding is evaluated for a Kazakhstani oilfield by systematically screening the chemical constituents involved. Field A in Kazakhstan, one of the oldest fields in the country, has been waterflooded for decades and has not produced even 50% of the original oil in place (OOIP). Currently, the water cut of the field is more than 90%, with a high residual oil saturation. Therefore, besides polymer flooding to control mobility, chemical EOR is proposed as a tertiary recovery method to mobilize residual oil. This study aimed to screen chemicals, including surfactant, alkali, and NPs, to design an effective AS/NS flooding program for the target field. The study focused on conducting laboratory experiments to identify the most effective surfactant and further optimize its performance by screening suitable alkaline and NPs based on their compatibility, stability, and adsorption behavior under reservoir conditions. The performance of the screened chemicals in the porous media was analyzed by a set of coreflood experiments. The findings of the study indicated that alkali agents, particularly sodium carbonate, positively affected surfactant performance by reducing its adsorption by 9–21%. The most effective surfactant combination was found, which gave Winsor type III microemulsion and the lowest interfacial tension (IFT) of 0.2 mN/m. The coreflood tests were conducted with the screened surfactant, alkali, and NPs. Both AS and NS tests demonstrated high residual oil recovery and microemulsion production. However, NS flooding performed better as the incremental oil recovery by NS flooding was 5% higher than standalone surfactant flooding and 9% higher than AS flooding. The results of this screening study helped in designing an efficient chemical formulation to improve the remaining oil recovery from Field A. The findings of this study can be used to design EOR projects for oil fields similar to Field A.
The application of polymer flooding is currently under investigation to control water cut and recover residual oil from a giant sandstone reservoir in Kazakhstan, where the water cut in most producers exceeds 90%, leaving substantial untouched oil in the porous media. The primary objective of this research is to explore the feasibility of a novel approach that combines the mechanisms of mobility control by polymer injection and the thermal effects, such as oil viscosity reduction, by utilizing hot water to prepare the polymer solution. This innovative hybrid method’s impact on parameters like oil recovery, resistance factor, and mobility was measured and analyzed. The research involved an oil displacement study conducted by injecting a hot polymer at a temperature of 85 °C, which is higher than the reservoir temperature. Incremental recovery achieved through hot polymer injection was then compared to the recovery by conventional polymer flooding and the conventional surfactant–polymer-enhanced oil recovery techniques. The governing mechanisms behind recovery, including reductions in oil viscosity, alterations in polymer rheology, and effective mobility control, were systematically studied to comprehend the influence of this proposed approach on sweep efficiency. Given the substantial volume of residual oil within the studied reservoir, the primary objective is to improve the sweep efficiency as much as possible. Conventional polymer flooding demonstrated a moderate incremental oil recovery rate of approximately 48%. However, with the implementation of the new hybrid method, the recovery rate increased to more than 52%, reflecting a 4% improvement. Despite the polymer’s lower viscosity during hot polymer flooding, which was observed by the lower pressure drop in contrast to the conventional polymer flooding scenario, the recovery factor was higher. This discrepancy indicates that while polymer viscosity decreases, the activation of other oil displacement mechanisms contributes to higher oil production. Applying hybrid enhanced oil recovery mechanisms presents an opportunity to reduce project costs. For instance, achieving comparable results with lower chemical concentrations is of practical significance. The potential impact of this work on enhancing the profitability of chemically enhanced oil recovery within the sandstone reservoir under study is critical.
Spontaneous imbibition (SI) is the key mechanism governing oil production in fractured carbonates, where capillary forces drive oil from the low-permeability matrix into the fractures. Its application is limited by the strongly oil-wet nature of carbonate rocks and by high interfacial tension (IFT), which restrict the capillary forces needed to mobilize oil from the matrix. This work examines whether a combined low-salinity water (LSW)-surfactant enhanced oil recovery (EOR) process can be optimized for SI by tuning the potential determining ions (PDIs) of the hybrid-stage brine. Experiments were performed with a fixed LSW preconditioning stage, while the hybrid-stage composition and surfactant concentration were varied. Contact angle screening of three ion-modified LSW formulations showed that LSW3Ca3Mg-SO4, with tripled Ca2+ and Mg2+, reduced the contact angle from 178.5° to 47.3° within 6 days and lowered the IFT from 33.2 to 17.5 mN/m without surfactant. In SI tests on limestone cores, ion-modified hybrid systems showed substantially higher early-time imbibition rates than conventional LSW-surfactant systems, together with equal or higher ultimate recovery. Notably, with 0.5 wt.% surfactant the ion-modified system reached an early-time rate of 0.75%/h and 36.36% of the original oil in place (OOIP), compared with 0.36%/h and 35.94% OOIP for conventional LSW with 1.0 wt.% surfactant, i.e., at half the surfactant dosage. Wettability-controlled systems, such as ion-modified LSW without surfactant, accelerate early imbibition but recover only about 6–7% OOIP regardless of ionic tuning. IFT reduction, in contrast, is considered to lower the capillary resistance in tight pore throats, allowing much higher recovery even while the rock surface remains oil-wet (40.15% OOIP with the ion-modified hybrid system at 1.0 wt.% surfactant). These findings suggest that tuning the ionic composition of the hybrid-stage brine can accelerate SI and allow a lower surfactant dosage, pointing to a potentially cost-effective ionic design strategy for EOR in fractured carbonate reservoirs.