Curvature-based damage detection has been previously applied to identify damage in concrete structures, but little attention has been given to the capacity of this method to identify distributed damage in multiple damage zones. This study aims to apply for the first time an enhanced existing method based on modal curvature analysis combined with wavelet transform curvature (WTC) to identify zones and highlight the damage zones of a beam made of ultra-high-performance fiber-reinforced concrete (UHPFRC), a construction material that is emerging worldwide for its outstanding performance and durability. First, three beams with a 2 m span of UHPFRC material were cast, and damaged zones were created by sawing. A reference beam without cracks was also cast. The free vibration responses were measured by 12 accelerometers and calculated by operational modal analysis. Moreover, for the sake of comparison, a finite element model (FEM) was also applied to two identical beams to generate numerical acceleration without noise. Second, the modal curvature was calculated for different modes for both experimental and FEM-simulated acceleration after applying cubic spline interpolation. Finally, two damage identification methods were considered: (i) the damage index (DI), based on averaging the quadratic difference of the local curvature with respect to the reference beam, and (ii) the WTC method, applied to the quadratic difference of the local curvature with respect the reference beam. The results indicate that the developed coupled modal curvature WTC method can better identify the damaged zones of UHPFRC beams.
Traditionally, initial material cost has been the governing factor for material selection in structural construction. However, the growing maintenance cost of existing infrastructure has demanded a long-term vision in material selection and in this regard, life cycle cost assessment has been proven to be a better assessment tool than the initial cost of construction. Despite its higher initial cost, aluminum offers many positive attributes, such as a high resistance to weight ratio, good recyclability, and excellent corrosion resistance, which can significantly reduce the life cycle cost of a structure over its entire service life. Yet, the limited use of aluminum in bridge construction and the lack of literature on this matter do not provide comprehensive evidence of its superior performance in the long-term. Based on this premise, this study performs a life cycle cost analysis on the first all-aluminum bridge situated in Arvida, Quebec. The analysis has revealed that most maintenance costs are associated with the rehabilitation of the concrete deck. The frequent concrete deck maintenance dismisses the benefits of the low maintenance aluminum structure. In order to investigate further, an alternative analysis has also been performed on the bridge with a hypothetical aluminum deck that replaces the existing concrete deck. The comparison shows that the aluminum deck reduces the maintenance cost significantly. However, further analysis should be performed with an optimized aluminum deck that can also yield a significantly lower life cycle cost compared to the existing bridge.
This paper investigates the ultimate resistance of aluminum circular hollow sections (C.H.S.) under simple load cases as affected by local buckling and material strain hardening. Following the development of advanced non-linear shell finite element models and their validation against existing test data, extensive non-linear numerical analyses were carried out, varying several key parameters such as alloy types, load case (compression or pure bending) and various section dimensions. The numerical results are used as references to analyze the structural performance of aluminum C.H.S., and to assess the accuracy of design equations based on the Overall Interaction Concept (O.I.C.). The O.I.C.-based proposal is shown to yield more accurate, consistent, and continuous resistance predictions than Eurocode 9 recommendations.
Due to its high strength-to-weight ratio, corrosion resistance, extrudability, and recyclability, there is a growing demand for the use of aluminum for sustainable bridge constructions, especially for footbridges. Owing to their light weight and lively characteristics, vibration serviceability often governs the design of aluminum footbridges. To better design these bridges, it is necessary to accurately predict pedestrian-induced walking loads. To this end, the existing design codes around the world have adopted the periodic moving force model (MF) due to its simplicity. However, the appropriateness of the MF model is being questioned, mainly in capturing the effect of the human–structure interaction (HSI), which can be pertinent to the design behavior of aluminum footbridges. A biomechanical-based spring-mass-damper (SMD) model was developed in the literature to simulate the HSI phenomena, which has never been validated for aluminum footbridges. Moreover, to simplify the complexity associated with SMD models, the experimental moving force model (EMF) was developed that can capture the effect of the HSI in an equivalent sense. This study aims to evaluate the capability of the SMD and EMF models to capture the real behavior of aluminum footbridges. To do so, the vibration responses of two aluminum footbridges are simulated numerically as a single-degree-of-freedom (SDOF) system under single-pedestrian walking loads employing the SMD, EMF, and MF models, which are then compared and validated based on already-available experimental observations. Finally, recommendations are made for the most suitable model for the vibration prediction of aluminum footbridges.
This study investigates the buckling behaviour of extruded aluminum square and rectangular hollow section (SHS/RHS) members under compression and combined loading. An experimental programme was conducted to examine the response of aluminum members subjected to eccentric compression. The experimental results were used to validate detailed finite element models developed in Abaqus, which were subsequently employed in an extensive parametric study. The outcomes of this study are intended to support the development of new design rules based on the Overall Interaction Concept (O.I.C.).