This study reports on the numerical analysis of the impact of mass ratio on the Vortex-Induced Vibration (VIV) phenomenon of an elastically rigid cylinder, oscillating freely in a crossflow direction. Reynolds-averaged Navier–Stokes (RANS) equations with (k-ω SST) model were used to analyze the flow behavior, amplitude ratio and vortex shedding patterns. The study was performed at constant Reynold number (Re) = 10⁴ with reduced velocity (U_r) ranging from 2 to 14 and mass ratio (m*) of 2.4 and 11. The mass ratio was defined as the ratio between mass of the vibrating cylinder and mass of the fluid displaced. It was found that increasing the mass ratio from 2.4 to 11 resulted in decrease in amplitude response by 80%, 71% and 31% at initial branch, upper to lower transition region and lower branch, respectively. However, the amplitude in the upper branch decreased only 8% at high mass ratio. The peak amplitude observed in the present study was lower than previous experimental and DES results. However, the RANS k-ω SST well captured the vortex shedding modes of 2S, 2P, P + S, and 2T. In 2S mode, two single pairs of vortices were formed, whereas in 2P mode two pairs were generated in single oscillation. Similarly, P + S meant one pair and one individual vortex; whereas 2T mode meant two triplets of vortices generated in one oscillation. The study concluded that increase in mass ratio results in shortening of the lock-in region and decrease in amplitude response.

The interface debonding in carbon fiber-reinforced polymers is analyzed and evaluated using the extended finite element method (XFEM). In order to accurately evaluate the bonding properties between fibers and matrix, different tests were carried out, including the multiple tests for different orientations to study longitudinal, transversal, and shear properties of unidirectional carbon fiber-reinforced composites. Extensive experimentation has been performed in all the different groups and categories with different dimensions and parameters in order to ascertain the values of strength and the prediction of the damage to the structure. The experimental and numerical comparison provided significant trends and data to evaluate the mechanical properties of the interface. The values of stiffness and strength are compared and validated. Development of Representative Volume Element (RVE) for progressive damage model to these damage phenomena has already been performed as a feasibility study for the model, though it is not included in this particular paper. The results of this research for all the experimental and numerical sets can serve as reliable data in the microsimulation of devices and sensitive parameters that include carbon fiber-reinforced light metal matrix composites and makes a better investigative model that contributes to various conditions. It further offers an investigation of the microscopic deformation mechanisms in the composites.

Fluid–structure interaction has been widely studied in the last few decades due to its wide range of applications in engineering fields. This phenomenon plays an important design role, for example, in offshore risers, high slender buildings, chimney stacks and heat exchangers. The vortex shedding generated from a bluff body can induce high-amplitude oscillations, known as vortex-induced vibrations (VIVs). This study presents a numerical analysis to investigate the impact of surface roughness on VIV in the crossflow direction of a circular cylinder. The study also investigates the impact of surface roughness with variation in mass ratio from 2.4 to 11 at a high Reynolds number (Re) = 10⁴ using Reynolds-averaged Navier–Stokes (RANS) equations. The study concludes that roughness on a cylinder results in a reduction in amplitude response. Furthermore, the lock-in region is narrower compared to that of a smooth cylinder, irrespective of the mass ratio. However, it is observed that the impact of surface roughness is more significant in high-mass-ratio cylinders where the lock-in region is more squeezed and shifted toward lower reduced velocities. Furthermore, the vortex mode beyond reduced velocities Ur = 5.84 and 7.52 was observed to be 2S for high and low mass ratios, respectively.

Gas natural convection is one common phenomenon in industrial applications, especially for the thermal management of electronic devices. In this study, a numerical model for gas natural convection in a confined porous cavity is constructed based on the lattice Boltzmann (LB) method, which predicts the density-difference-induced flow using a multiple relaxation time (MRT) collision operator. At the gas–solid interfaces, the microscale flow and heat transfer effects are formulated using an effective slip boundary condition. The established LB model is applied to investigate the Nusselt number for heated obstacles arranged in a staggered formation in the cavity. Based on the calculated data, the Nusselt number values obtained for a five-cylinder pore-scale (single pore, SP) domain are analyzed and compared to those for a 13-cylinder (multipore, MP) one. The Nusselt number shows a sharp decrease as soon as the microscale effect is considered at the obstacle walls. It was also observed that the Nusselt number for MP domain achieved lower values than that of SP one. The findings in this work can contribute to the design of thermal management device with confined porous media.