Zhongjie Zhang

Zhongjie Zhang


Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2017 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
ZZZhongjie Zhang
Zhongjie Zhang
ZZZhongjie Zhang
Zhongjie Zhang
SDSurong Dong
Surong Dong
GZGuangmeng Zhou
Guangmeng Zhou
To improve engine power at high altitude, the regulated two-stage turbocharger (RTST) which was applied to different altitudes was developed by the authors. The working process model of heavy-duty common-rail diesel engine matched with RTST was built to study the regulating characteristic of variable geometry turbocharger (VGT) vane and both turbine bypass valves and also matching performance of RTST with engine at different altitudes. The control scheme of RTST at different altitudes and engine operating conditions was first put forward, and the optimal opening maps of VGT vane and both turbine bypass valves at different altitudes and engine operating conditions were obtained. The results show that the optimal openings of VGT vane and both turbine bypass valves decrease with increase of altitude, and the optimal opening range of VGT vane becomes narrower with increase of altitude. The operating points of both high-pressure (HP) and low-pressure (LP) compressors locate at high-efficiency region of each compressor map, respectively, and compressor efficiency exceeds 70% at altitude of 5500 m. The total boost pressure ratio increases with altitude and reaches the maximum value of 5.1 at altitude of 5500 m. Compared with single-stage turbocharged engine, the rated power, maximum torque, and torques at lower engine speed at altitude of 5500 m increase by 48.2%, 51%, and 65–121% separately, and the minimum fuel consumption decreases by 12.6%.

24 April 2018 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Open access
MMMomen Mousa
Momen Mousa
Mostafa ElseifiMostafa Elseifi
Mostafa Elseifi
MBMohammad Bashar
Mohammad Bashar
ZZZhongjie Zhang
Zhongjie Zhang
KGKevin Gaspard
Kevin Gaspard
One of the most common methods used to treat longitudinal and transverse cracks is crack sealing (CS), which is categorized as a preventive maintenance method. Field performance and cost-effectiveness of this treatment widely vary depending on pavement conditions and installation of the material. The objective of this study was to evaluate the field performance and cost-effectiveness of CS in flexible and composite pavements in hot and wet climates such as Louisiana, and to develop a model that would quantify the expected benefits of CS given project conditions. To achieve this objective, 28 control sections that were crack-sealed between 2003 and 2010 were monitored for at least four years. These sections included flexible and composite pavements, sealed and unsealed segments, and varying traffic levels. The performance of these sections was evaluated for the random cracking index (RCI) and roughness index (RI). Based on the results of this analysis, it was concluded that CS only has a significant impact on random cracking. When compared with untreated segments, CS extended pavement service life (PSL) by two years. When compared with the original pavement, CS extended PSL by 5.6 and 3.2 years for flexible and composite pavements, respectively, if applied at the correct time. The cost-benefit analysis indicated that CS is cost-effective whether asphalt emulsion or rubberized asphalt sealant is used. A non-linear regression model was developed to predict the extension in PSL because of CS without the need for performance data based on the average daily traffic (ADT), pavement type, and prior pavement conditions.

21 April 2019 in International Journal of Aerospace Engineering
Verified
Journal Article
Open access
RLRui-Lin Liu
Rui-Lin Liu
ZZZhongjie Zhang
Zhongjie Zhang
YJYu-Fei Jiao
Yu-Fei Jiao
CYChun-Hao Yang
Chun-Hao Yang
WZWen-Jian Zhang
Wen-Jian Zhang
The engine performance test at altitudes of 0-7000 m was carried out on the high-performance test bench of the Unmanned Aerial Vehicle (UAV) piston engine. The flight performance of UAV was studied, including propeller thrust characteristics, maneuverability, flight envelope, and cruise performance. The results showed that with the increase in altitudes, the UAV climb rate gradually decreased; the maximum climb rate decreased from 2.5 m/s at 2000 m to 0.5 m/s at 7000 m. The maximum flight altitude is 7000 m, and the flight speed range is about 47 m/s-52 m/s at the altitude of 7000 m. Maximum navigation range and endurance of UAV decrease by 5.8% and 8%, respectively, with each increment of 1000 m in altitudes.

23 April 2018 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Open access
ZZZia Uddin Ahmed Zihan
Zia Uddin Ahmed Zihan
Mostafa ElseifiMostafa Elseifi
Mostafa Elseifi
KGKevin Gaspard
Kevin Gaspard
ZZZhongjie Zhang
Zhongjie Zhang
The importance of incorporating pavement structural conditions in the selection of maintenance and rehabilitation strategies along with functional indices has been recognized by state agencies. To measure in-service pavement structural capacity, surface deflection under a defined load has been typically used. The traffic speed deflectometer (TSD) has emerged as a continuous deflection-measuring device as it operates at traffic speed and reduces lane closure and user delays. The present study developed a nonlinear regression model to predict pavement structural number (SN) based on surface deflections measured by the TSD along with the total pavement layer thickness and traffic volume. The proposed model was successfully developed and validated with SN calculated based on TSD and falling weight deflectometer deflection data obtained from two testing programs in Louisiana and Idaho. The model was further validated with respect to its prediction of in-service structural capacity loss and deficiency. Based on statistical measures and the model’s ability in identifying structurally deficient sections, results showed satisfactory accuracy of the model and supports its use for network-level decision-making processes in the pavement management system.

27 July 2023 in ACS Omega
Verified
Journal Article
Open access
QPQi-kai Peng
Qi-kai Peng
RLRuilin Liu
Ruilin Liu
GZGuangmeng Zhou
Guangmeng Zhou
XZXumin Zhao
Xumin Zhao
SDSurong Dong
Surong Dong
HZHan Zhang
Han Zhang
The increase in altitude causes the decrease in internal combustion engine power and the increase in pollutant emission. Converting waste heat into more useful forms of energy through the recovery of waste heat from internal combustion engines is the most promising mechanism for improving both of these goals. This paper comprehensively reviews the development and research of waste heat recovery technology of an internal combustion engine in a variable altitude environment. It is found that exhaust gas turbocharging is the most promising waste heat recovery technology to restore high-altitude internal combustion engine power. Turbochargers are affected by low temperature and low pressure at high altitudes, resulting in poor environmental adaptability, inadequate supercharging ratios, and decreased supercharging efficiency. Therefore, it is very important to select the high pressurization system facing the plateau area and its reasonable matching characteristics. The quality of exhaust energy determines how much waste heat a turbine can recover, and only the exergy part of exhaust energy can realize heat/work conversion. The main disadvantage of turbocharging technology applied in the plateau area is that the speed ratio deviates from the design value, leading to the increase of flow loss inside the supercharger. Therefore, optimizing the internal flow field of a high-altitude supercharger is a key problem to improve the efficiency of energy recovery. The conclusion drawn from this Review is that a two-stage turbocharging system will be a key technology to improve the thermal efficiency and reduce the fuel consumption of high-altitude internal combustion engines in the coming decades. In addition, the efficient utilization of the exhaust energy of the two-stage turbine and the influence of the variable compression process of the two-stage compressor on the working medium in the cylinder will be the focus of future research.

28 March 2022 in Applied Thermal Engineering
Verified
Journal Article
Closed access
ZZZhongjie Zhang
Zhongjie Zhang
RLRuilin Liu
Ruilin Liu
SDSurong Dong
Surong Dong
GZGuangmeng Zhou
Guangmeng Zhou
WLWuquan Liu
Wuquan Liu
QPQikai Peng
Qikai Peng