Arthur Filgueira de Almeida

Dr. Arthur Filgueira de Almeida

Mechanical Engineering, Federal University of Campina Grande, Campina Grande, Paraíba, Brazil
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2024 in Metals
Verified
Journal Article
Open access
PDF file
MSMathews Lima dos Santos
Mathews Lima dos Santos
AAArthur Filgueira de Almeida
Arthur Filgueira de Almeida
GFGuilherme Gadelha de Sousa Figueiredo
Guilherme Gadelha de Sousa Figueiredo
MSMarcos Mesquita da Silva
Marcos Mesquita da Silva
TMTheophilo Moura Maciel
Theophilo Moura Maciel
RSRenato Alexandre Costa de Santana
Renato Alexandre Costa de Santana
The influence of the centerline segregation region (CSR) on the hydrogen embrittlement (HE) of two different API 5L X80 pipeline steel plates was investigated. The novelty of this work was to establish relationships between the CSR, microstructure, and distribution of localized fragile particles on HE susceptibility and on fracture morphology. This work intended to establish a relationship between centerline segregation and HE susceptibility in high-strength low-alloy steels submitted to inhomogeneous transformations. Microscopy, hydrogen permeation, and slow strain rate (SSR) tests were used to investigate hydrogen-related degradation. The solution used on the charging cell of the permeation tests—and on the SSR test cell—was 0.5 mol L−1 H2SO4 + 10 mg L−1 As2O3, and in the oxidation cell, 0.1 M NaOH was used as a solution. The CSR led the thicker plate to present the highest HE index (0.612) in analyses carried out in the mid-thickness; however, the same plate showed the lowest HE index in near-surface tests. The presence of hydrogen changed the fracture morphology from ductile to a brittle and ductile feature; this occurred due to the interaction with localized fragile particles and the significant reduction of the shear stress necessary for the dislocation movement.

21 January 2021 in The Canadian Journal of Chemical Engineering
Verified
Journal Article
Closed access
PDF file
AAArthur Filgueira de Almeida
Arthur Filgueira de Almeida
HNHeleno da Costa Neto
Heleno da Costa Neto
RSRenato Alexandre Costa de Santana
Renato Alexandre Costa de Santana
JAJosé J. N. Alves
José J. N. Alves
ACAna Regina Nascimento Campos
Ana Regina Nascimento Campos
SPShiva Prasad
Shiva Prasad

26 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
Josiane Dantas CostaJosiane Dantas Costa
Josiane Dantas Costa
AAArthur Filgueira de Almeida
Arthur Filgueira de Almeida
RSRenato Alexandre Costa de Santana
Renato Alexandre Costa de Santana
ACAna Regina Nascimento Campos
Ana Regina Nascimento Campos
JOJosé Anderson Machado Oliveira
José Anderson Machado Oliveira
Antonio Gilson Barbosa de LimaAntonio Gilson Barbosa de Lima
Antonio Gilson Barbosa de Lima
The effect of current density and bath temperature in the electroplating process on resistance to corrosion of Zn-Ni alloys was evaluated in this work. The electrolytic bath consisted of nickel sulfate, zinc sulfate, sodium sulfate, boric acid, and sodium citrate at pH 7.0. The current density was varied in the range 20–80 mA/cm2 and the bath temperature in the range 30–60 °C. Increasing, independently, the current density or the bath temperature increased the nickel content in the obtained alloy, which affected the alloy microstructure, with a predominant γ phase and cauliflower-like morphology. The nickel content in the alloys was in the range 20–42%wt. A synergistic effect between the current density and bath temperature was observed from a design of experiments and response surface models. The maximum resistance to corrosion occurred for the alloy containing 42%wt. nickel. This alloy was obtained at upper levels of current density and bath temperature, presenting a corrosion potential of −0.789 V and polarization resistance of 4136 Ω.cm2.

24 January 2025 in Coatings
Verified
Journal Article
Open access
PDF file
ÉSÉvany SILVA Silva dos Santos
Évany SILVA Silva dos Santos
Josiane Dantas CostaJosiane Dantas Costa
Josiane Dantas Costa
AAArthur Filgueira de Almeida
Arthur Filgueira de Almeida
ASAureliano Xavier dos Santos
Aureliano Xavier dos Santos
LALincoln Rodrigues Sampaio de Araujo
Lincoln Rodrigues Sampaio de Araujo
ACAna Regina Nascimento Campos
Ana Regina Nascimento Campos
In this study, nickel–cobalt (Ni–Co) coatings were fabricated via electrodeposition using a 22 central composite factorial design with two central and two axial points, totaling ten experiments. The effects of pH and current density on the coatings’ chemical composition and properties were evaluated. Coatings were characterized by microstructure, morphology, magnetic properties, and corrosion resistance. The results showed that pH significantly influenced chemical composition, while current density had no notable effect. Acidic pH produced cobalt-rich coatings (43–81 at.%), with uniform morphology, higher saturation magnetization, and lower corrosion resistance. Maximum cobalt content (81 at.%) resulted in a mixed face-centered cubic (fcc) + hexagonal close-packed (hcp) phase. Alkaline pH yielded nickel-rich coatings (89–95 at.%), featuring nodular morphology, lower magnetization, higher corrosion resistance, and, exclusively, the fcc phase. The highest polarization resistance (66.1 kΩ) occurred at pH 8.83 and 60 mA/cm2, while resistance decreased with increasing cobalt content. The pH effect on deposition was linked to the formation of citrate complexes: ammonia and citrate complexes promoted nickel deposition under alkaline conditions, while stable cobalt complexes dominated in an acidic pH. These findings highlight the potential to tailor Ni–Co coatings for applications such as corrosion-resistant coatings (nickel-rich) or magnetic devices (cobalt-rich).

23 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
Josiane Dantas CostaJosiane Dantas Costa
Josiane Dantas Costa
MSMikarla B. Sousa
Mikarla B. Sousa
AAArthur Filgueira de Almeida
Arthur Filgueira de Almeida
JOJosé Anderson Machado Oliveira
José Anderson Machado Oliveira
PSPaulo César Sales da Silva
Paulo César Sales da Silva
Antonio Gilson Barbosa de LimaAntonio Gilson Barbosa de Lima
Antonio Gilson Barbosa de Lima
This study aims to manufacture and characterize titanium and nickel alloys with different molybdenum (Ti–Ni–Mo) contents, focusing on the influence of these additions on the microstructure, mechanical properties, and corrosion resistance. The relevance of this work stems from the lack of research on this specific alloy and the absence of reports in the literature with molybdenum percentages above 2 at.%. Ti50Ni50−XMox alloys were produced by the plasma arc melting method, with six different compositions (x = 0, 0.5, 1, 2, 3, and 4 at.% Mo), and a comprehensive analysis of microstructure, chemical composition, thermal, mechanical, and electrochemical properties was carried out. The results demonstrated significant alterations in the microstructure of the Ni–Ti alloy with the addition of molybdenum presenting several phases, precipitates (TiNi, Ti2Ni), and oxides (Ti4Ni2O, TiO, and TiO3). The stability of the B2 phase increased with molybdenum content, and the monoclinic martensite (B19′) phase was identified only in the Ni–Ti sample. Introducing molybdenum into the Ni–Ti alloy generated the R-phase and shifted the phase transformation peaks to lower temperatures, as differential scanning calorimetry (DSC) indicated. Microhardness and elastic modulus decreased with increasing Mo content, ranging from 494 HV to 272 HV and 74 GPa to 63 GPa, respectively. Corrosion tests revealed increased corrosion resistance with increasing Mo content, reaching a polarization resistance of 2710 kΩ·cm2 and corrosion current of 11.3 µA. Therefore, this study points to Ti–Ni–Mo alloys as potential candidates to increase the range of Ni–Ti alloy applications, mainly in biomaterials, reinforcing its relevance and need in current alloy research.

7 August 2020 in Research, Society and Development
Verified
Journal Article
Open access
PDF file
Josiane Dantas CostaJosiane Dantas Costa
Josiane Dantas Costa
JOJosé Anderson Machado Oliveira
José Anderson Machado Oliveira
AOAlison Silva Oliveira
Alison Silva Oliveira
ARAnamélia de Medeiros Dantas Raulino
Anamélia de Medeiros Dantas Raulino
JRJosé Leonardo Costa Raulino
José Leonardo Costa Raulino
RSRenato Alexandre Costa de Santana
Renato Alexandre Costa de Santana
Foram avaliados os efeitos da densidade de corrente e agitação mecânica do banho no processo de eletrodeposição para obtenção da liga Zn-Ni. Foi utilizado um banho eletrolítico constituído de sulfato de níquel, sulfato de zinco, sulfato de sódio, ácido bórico e citrato de sódio em pH 7,0. A densidade de corrente foi avaliada na faixa de 10-50 mA/cm² e para a agitação mecânica foi avaliada na faixa de 30-70 rpm. Como ferramenta de otimização, foi utilizado um planejamento fatorial completo 2² com três elementos centrais associado à Metodologia de Superfície de Resposta (MSR). Foi observado que o aumento da densidade de corrente e da agitação mecânica provocou o aumento do percentual atômico de níquel nos revestimentos. O percentual de zinco aumentou com a diminuição da densidade de corrente. O ponto ótimo de níquel obtido foi de 39 at.%. A eletrodeposição foi do tipo anômala. A microdureza aumentou com o aumento do percentual de níquel e com a diminuição do percentual de Zn no revestimento. Os revestimentos apresentaram nódulos na superfície com diferentes tamanhos e formas.