The influence of the centerline segregation region (CSR) on the hydrogen embrittlement (HE) of two different API 5L X80 pipeline steel plates was investigated. The novelty of this work was to establish relationships between the CSR, microstructure, and distribution of localized fragile particles on HE susceptibility and on fracture morphology. This work intended to establish a relationship between centerline segregation and HE susceptibility in high-strength low-alloy steels submitted to inhomogeneous transformations. Microscopy, hydrogen permeation, and slow strain rate (SSR) tests were used to investigate hydrogen-related degradation. The solution used on the charging cell of the permeation tests—and on the SSR test cell—was 0.5 mol L−1 H2SO4 + 10 mg L−1 As2O3, and in the oxidation cell, 0.1 M NaOH was used as a solution. The CSR led the thicker plate to present the highest HE index (0.612) in analyses carried out in the mid-thickness; however, the same plate showed the lowest HE index in near-surface tests. The presence of hydrogen changed the fracture morphology from ductile to a brittle and ductile feature; this occurred due to the interaction with localized fragile particles and the significant reduction of the shear stress necessary for the dislocation movement.
Duplex stainless steels are largely applied in petrochemical industries due to their high corrosion resistance and mechanical performance. Their applicability also requires a great wear resistance, which can be enhanced by friction stir processing (FSP), a surface hardening technique. In this work, FSP is utilized to process surfaces of UNS S32101 and UNS S32750. The materials were analyzed by EBSD in order to determine grain size and phase fraction. Microhardness tests were used to verify and compare the shifting of hardness values from 296 ± 8 to 314 ± 11 HV 0.2/15 and from 323 ± 8 to 350 ± 8 HV 0.2/15 for UNS S32101 and S32750, respectively. Abrasion tests were executed to study the wear behavior of both processed and unprocessed alloys. Abrasion tests indicated that the hardening by FSP promoted decrement of abrasive wear resistance. Volumetric loss increased after FSP, from 52.1 ± 0.5 to 53 ± 2 mm 3 , for UNS S32101, and from 50 ± 2 to 56.3 ± 0.3 mm 3 for UNS S32750. Tensile tests results were fitted to Hollomon's equation in order to identify mechanical properties and tendencies of strain hardening. SEM images were used to classify the wear micromechanisms acting on the samples. The results suggest that FSP can promote modifications of wear mechanisms and these changes can be correlated to the alloys' microstructure.
22 January 2026 in The International Journal of Advanced Manufacturing Technology
Wire Arc Additive Manufacturing (WAAM) has emerged as a competitive fabrication technique for stainless steel components in nuclear, marine, aerospace, and cryogenic sectors, owing to its low cost and high deposition rates. These industries commonly take advantage of stainless steel components, due to their great corrosion resistance and high mechanical performance, which are tied to their microstructural characteristics. Although studies have explored the microstructural evolution in Gas Metal Arc Additive Manufacturing (GMA-AM), little is known about the distinct effects of current pulsing in the Wire and Pulsed Arc Additive Manufacturing (WPAAM) variant. This study investigates the microstructure and local mechanical response of a multilayered 316LSi stainless steel thin wall fabricated by WPAAM. The deposit exhibited diverse δ-ferrite morphologies (vermicular, lacy, acicular and globular), especially at interlayer locations, where rapid cooling and arc pulsing caused localized transitions. Microstructural banding of type 1 was observed, attributed to periodic dendritic fragmentation under non-equilibrium solidification conditions. Cooling rates, estimated from dendritic arm spacing, ranged from 6.44 × 10³ K/s to 3.48 × 10² K/s. Such rates, typically found in high-energy beam processes, were achieved through precise arc modulation. Hardness variations were linked to local δ-ferrite morphology and fragmentation, with implications for performance optimization. These findings extend the current understanding of WPAAM and highlight its potential to tailor microstructural features through process control.
21 August 2020 in Revista Mundi Engenharia, Tecnologia e Gestão (ISSN: 2525-4782)
This contribution offers a study for two numerical approaches of FSW joints for the API 5L-X80 steel. The first one, a pure thermal model, takes into consideration the preponderant frictional force of the tool being in contact with the workpiece. The second model is a computational fluid dynamic approach, which involves determining experimental values for physical constants and observing its influence in viscous dissipation and strain rates of the material. Temperature and thermal history from the FSW processing were recorded and analyzed. The acquired data was provided from two different heat input conditions. In cases of previewing tool or workpiece local temperature, the pure thermal model is a sufficient suitable approach. Conversely, the CFD model frequently requires huge amounts of information, regarding physical constants and experimental variables, becoming a delicate task for its construction. The pure thermal model was able to offer unequivocal temperature results without the need for large experimental data acquisition. This approach was considered to be finer employed when one aims to forecast temperatures in regions proximate to the welding line. The natural complexity associated with FSW processing suggests there are enormous quantities of experimental factors to be considered for the numerical modeling of high-temperature materials. Also, the CFD approach offers distinct results, which might be crucial for understanding the full aspects of experimental variables. A coupled numerical approach with both models is suggested to fully represent the thermophysical aspects of FSW processing.