The purpose of this work was to investigate the structural, thermal, micromechanical and tribological properties of novel polymer/metal composite materials for bearing applications. Copper (Cu)-filled Acrylonitrile Butadiene Styrene (ABS) composites were mixed in a laboratory scale by an internal mixer with two blade impellers, and then injection-molded. Neat ABS, ABS+5wt% Cu, ABS+10wt% Cu, and ABS+15wt% Cu were the four materials that were tested. The dispersion of Cu particles in the ABS matrix was investigated using Scanning Electron Microscopy (SEM) and a micro-tomography scan. The filler particles have a uniform distribution in the matrix, according to the observations. The incorporation of Cu filler also refined an increase in the glass transition temperature from Differential Scanning Calorimetry (DSC) and less intensity in the amorphous phase by X-ray diffraction (XRD). Nanoindentation tests were carried out to characterize the micro-mechanical behavior of the composites. Friction and wear analysis were also examined using a pin-on-disk tribometer. Compared with neat ABS, all the micro-composites showed much higher indentation hardness, Vickers hardness, and indentation elastic modulus. It was also concluded that the incorporation of Cu filler into ABS simultaneously improved the friction and wear properties of the composites, which contributed to the suitability of the micro-filled composites with hard metallic particles for a wider range of mechanical components for bearing applications.
Polyamide 66 (PA66) has been used for dynamic bearing applications due to its good wear and abrasion resistance, hardness, and rigidity. PA66/copper micro-composites were studied with respect to micro-mechanical, tribological, and structural properties. A mixing step followed by injection molding was used to develop the different composites: PA66+5 wt.% Cu, PA66+10 wt.% Cu, and PA66+15 wt.% Cu. The morphological aspects of the composites were studied using scanning electron microscopy and microtomography. Good dispersion and adhesion of Cu particles across the matrix were also seen. DSC analysis showed a slight improvement in the % of crystallinity and thermal characteristics of the composites, particularly with 5 wt.% filler. Additional crystallization enhanced the tensile performance of the composites, including the modulus, elongation at break, and tensile strength. Nanoindentation tests also indicated an increase in indentation hardness and elastic modulus as a function of the filler fraction. A pin-on-disk tribometer was used to study the friction and wear properties of neat PA66 and copper-filled PA66 composites. It was found that the composite with 5 weight percent copper had the best wear resistance. A progressive decrease in the friction coefficient was also seen. Copper filler increases hardness and may effectively reduce the temperature at contact interfaces during rotating cycles.
The present research investigates the optimization of the punching process in cold forming manufacturing, focusing on enhancing tool life, reducing damage, and improving product quality. Punching, a shearing process widely used in sheet metal forming, requires careful management of process parameters to prevent tool damage, especially to the punch and die. The research explores various design modifications to the punching tool, including conical, pointed, and stepped shafts, aimed at reducing punching force and minimizing wear, fatigue, and crack formation. Using numerical simulations (ABAQUS/Explicit), the study evaluates the impact of shear angle, punch geometry, and other key parameters on the maximum punching force and stress distribution. The results show that adjusting the punch shaft shape and optimizing the shear angle can significantly decrease stress concentrations, extend tool lifespan, and improve process efficiency. This work provides valuable insights for improving punching tool designs and ensuring longer, more efficient service lives in industrial applications.
Punching is a widely adopted cold sheet metal forming process, prized for its cost-effectiveness and high production efficiency. However, premature tool failure remains a persistent challenge, leading to increased downtime and maintenance costs. This study investigates solutions to mitigate tool failure through a combination of 3D design optimization, Finite Element Modeling (FEM), and Response Surface Methodology (RSM). Specifically, FEM was used to analyze stress distribution and deformation in the punch under varying geometric and operational parameters, while RSM optimized the design space to identify key factors influencing tool life. The findings reveal that each proposed solution, including modifications to punch geometry, clearance, and material treatment, offers distinct advantages and trade-offs. A comparative analysis of these solutions highlighted one optimal design, which was then further analyzed using FEM to predict damage progression. While this study provides a framework for reducing tool failure, experimental validation of the damage prediction model is recommended for future work to confirm the numerical results. This research aims to provide industrial practitioners with actionable insights and methodologies to enhance punch durability, ultimately reducing production interruptions and costs.