Hyungmin Kim

Mr. Hyungmin Kim


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 March 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SPSangbin Park
Sangbin Park
YYYounghwa Yoon
Younghwa Yoon
HKHyungmin Kim
Hyungmin Kim
TPTaejun Park
Taejun Park
KKKyung Hwan Kim
Kyung Hwan Kim
JHJeongsoo Hong
Jeongsoo Hong
Controlling built-in potential can enhance the photoresponse performance of self-powered photodetectors. Among the methods for controlling the built-in potential of self-powered devices, postannealing is simpler, more efficient, and less expensive than ion doping and alternative material research. In this study, a CuO film was deposited on a β-Ga2O3 epitaxial layer via reactive sputtering with an FTS system, and a self-powered solar-blind photodetector was fabricated through a CuO/β-Ga2O3 heterojunction and postannealed at different temperatures. The postannealing process reduced the defects and dislocations at the interface between each layer and affected the electrical and structural properties of the CuO film. After postannealing at 300 °C, the carrier concentration of the CuO film increased from 4.24 × 1018 to 1.36 × 1020 cm−3, bringing the Fermi level toward the valence band of the CuO film and increasing the built-in potential of the CuO/β-Ga2O3 heterojunction. Thus, the photogenerated carriers were rapidly separated, increasing the sensitivity and response speed of the photodetector. The as-fabricated photodetector with 300 °C postannealing exhibited a photo-to-dark current ratio of 1.07 × 103; responsivity and detectivity of 30.3 mA/W and 1.10 × 1012 Jones, respectively; and fast rise and decay times of 12 ms and 14 ms, respectively. After three months of storage in an open-air space, the photocurrent density of the photodetector was maintained, indicating good stability with aging. These results suggest that the photocharacteristics of CuO/β-Ga2O3 heterojunction self-powered solar-blind photodetectors can be improved through built-in potential control using a postannealing process.

24 October 2023 in IEEE Sensors Journal
Verified
Journal Article
Closed access
HKHyungmin Kim
Hyungmin Kim
KKKyunghwan Kim
Kyunghwan Kim
JHJeongsoo Hong
Jeongsoo Hong
In this study, a high-performance deep ultraviolet p-i-n self-powered photodetector was successfully fabricated by controlling the Fermi level of the p-NiO and using an intrinsic β-Ga 2 O 3 layer. Controlling the oxygen flow rate during sputtering is one of the various techniques for adjusting the Fermi level of p-NiO. A Fermi level closer to the valence band results in a higher built-in potential of the photodetector based on p-NiO/i-β-Ga 2 O 3 /n-β-Ga 2 O 3 . As the oxygen flow rate increased from 2 to 4 SCCM, the barrier height increased from 1.08 eV to 1.43 eV. Moreover, the intrinsic layer of the photodetector can affect current density by increasing the photoactive layer and enhancing the response speed under the influence of a strong internal electric field. Thus, the photo-characteristics of the NiO/β-Ga 2 O 3 photodetector exhibited a current density of 144 μA/cm 2 , a responsivity of 182.5 mA/W, a detectivity of 6.61 × 10 12 Jones, and an external quantum efficiency of 89.3%, respectively. This study yields two noteworthy results. The first is the possibility of developing an unstudied DUV photodetector based on p-NiO/i-β-Ga 2 O 3 /n-β-Ga 2 O 3 . Second, a photodetector based on p-NiO can be improved by controlling the built-in potential and adjusting the oxygen flow rate.

6 April 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
YYYounghwa Yoon
Younghwa Yoon
SPSangbin Park
Sangbin Park
TPTaejun Park
Taejun Park
HKHyungmin Kim
Hyungmin Kim
KKKyung Hwan Kim
Kyung Hwan Kim
JHJeongsoo Hong
Jeongsoo Hong
A Ag:AZO electrode was used as an electrode for a self-powered solar-blind ultraviolet photodetector based on a Ag2O/β-Ga2O3 heterojunction. The Ag:AZO electrode was fabricated by co-sputtering Ag and AZO heterogeneous targets using the structural characteristics of a Facing Targets Sputtering (FTS) system with two-facing targets, and the electrical, crystallographic, structural, and optical properties of the fabricated thin film were evaluated. A photodetector was fabricated and evaluated based on the research results that the surface roughness of the electrode can reduce the light energy loss by reducing the scattering and reflectance of incident light energy and improving the trapping phenomenon between interfaces. The thickness of the electrodes was varied from 20 nm to 50 nm depending on the sputtering time. The optoelectronic properties were measured under 254 nm UV-C light, the on/off ratio of the 20 nm Ag:AZO electrode with the lowest surface roughness was 2.01 × 108, and the responsivity and detectivity were 56 mA/W and 6.99 × 1011 Jones, respectively. The Ag2O/β-Ga2O3-based solar-blind photodetector with a newly fabricated top electrode exhibited improved response with self-powered characteristics.

15 November 2023 in Coatings
Verified
Journal Article
Open access
PDF file
HKHyungmin Kim
Hyungmin Kim
KKKyung Hwan Kim
Kyung Hwan Kim
JHJeongsoo Hong
Jeongsoo Hong
In this study, NiO films were fabricated through radio frequency sputtering with various oxygen flow rates and processed via rapid thermal annealing under Ar, O2, and N2 atmospheres. The electrical, optical, and crystallographic properties of the NiO films were influenced by their oxygen content in each film. As the oxygen content, carrier concentration, and resistivity increased, transmittance and mobility decreased. The carrier mobility of the NiO film in the p-type layer of the photodetector requires improvement. Rapid thermal annealing (RTA) has been widely used to improve the crystallinity and mobility of films. However, the reduction in oxygen content during RTA causes a decrease in the carrier concentration and transmittance of NiO films. Regarding the aim of preventing a reduction in oxygen content in the NiO films due to the RTA process, an O2 atmosphere (compared with Ar and N2 atmospheres) was identified as the optimal condition for mobility (3.42 cm2/V·s) and transmittance (50%).

7 June 2023 in Coatings
Verified
Journal Article
Open access
PDF file
CJChoi Jiyoon
Choi Jiyoon
JSJiha Seong
Jiha Seong
SPSangbin Park
Sangbin Park
HKHyungmin Kim
Hyungmin Kim
Sangmo KimSangmo Kim
Sangmo Kim
JHJeong Soo Hong
Jeong Soo Hong
Ag2O thin films have been applied in various devices, such as photodetectors, photocatalysts, and gas sensors, because of their excellent thermal stability, strong electrical properties, and stable structures. However, because various phases of silver oxide exist, the fabrication of single-phase Ag2O thin films using a general deposition system is difficult. In this study, Ag2O thin films were deposited on glass substrates at different working pressures and O2 gas flow rates using a facing-target sputtering (FTS) system. After optimizing the working pressure and O2 gas flow rate, the Ag2O thin films were post-annealed at different temperatures ranging from 100 to 400 °C to improve their crystallographic properties. The X-ray diffraction patterns of the as-fabricated Ag2O thin films indicated the presence of a single phase of Ag2O, and the ultraviolet–visible (UV–vis) spectral analysis indicated transmittance of 65% in the visible light region. The optimum working pressure and O2 gas flow rate were determined to be 4 mTorr and 3.4 sccm, respectively. Finally, the effect of the post-annealing temperature on the thin film was investigated; the Ag2O peak had high intensity at 300 °C, suggesting this as the optimum post-annealing temperature.