A systematic study had been carried out to get insight into the micellar behavior of anionic lipopeptide (LT) and nonionic sophorolipid (SL) in their different mass ratio mixed state using the technique of tensiometry. The models proposed by Clint, Rubingh and Gibbs et al. had been employed to interpret the formation of mixed micelles and found out synergism. The obtained experimental critical micelle concentrations (CMC) were lower than the ideal CMCs, indicating negative deviation from ideal behavior for all multi-component mixed micelles formation. A suited binary bio-surfactant mixing system was selected as the washing agents to treat the oily sludge produced from Huabei oilfield by the thermal bio-surfactant washing method. The results showed that in case of the mass ratios of 8:2 the CMC was dramatically decreased and synergism was the strongest in LT and SL bi mixed surfactant systems. The studied binary mixed bio-surfactant system showed higher washing efficiency for oily sludge than single surfactant system. In addition, the washing power of binary mixed bio-surfactants towards oily sludge was the best at below washing conditions: (a) the concentration of the mixed system (100 mg/L), (b) temperature (55 ℃), (c) ratio of sludge/liquid (1:3), (d) washing time (3 h), and (e) stirring speed (300 rpm). Certainly, the washing abilities of the selected surfactants not only depend on their mixing ratio and washing conditions but also associate with microstructure and mineral components of oily sludge.

The chemically synthesized polymer polyacrylamide (HPAM) has achieved excellent oil displacement in conventional reservoirs, but its oil displacement is poor in extreme reservoir environments. To develop a biopolymer oil flooding agent suitable for extreme reservoir conditions, the viscosity changes and rheological properties of three biopolymers, diutan gum, xanthan gum, and scleroglucan, were studied under extreme reservoir conditions (high salt, high temperature, strong acid, and alkali), and the effects of temperature, mineralization, pH, and other factors on their viscosities and long-term stability were analyzed and compared. The results show that the three biopolymers had the best viscosity-increasing ability at temperatures of 90 °C and below. The viscosity of the three biopolymers was 80.94 mPa·s, 11.57 mPa·s, and 59.83 mPa·s, respectively, when the concentration was 1500 mg/L and the salinity 220 g/L. At the shear rate of 250 s⁻¹, 100 °C~140 °C, scleroglucan had the best viscosification. At 140 °C, the solution viscosity was 19.74 mPa·s, and the retention rate could reach 118.27%. The results of the long-term stability study showed that the solution viscosity of scleroglucan with a mineralization level of 220 mg/L was 89.54% viscosity retention in 40 days, and the diutan gum could be stabilized for 10 days, with the viscosity maintained at 90 mPa·s. All three biopolymers were highly acid- and alkali-resistant, with viscosity variations of less than 15% in the pH3~10 range. Rheological tests showed that the unique double-helix structure of diutan gum and the rigid triple-helix structure of scleroglucan caused them to have better viscoelastic properties than xanthan gum. Therefore, these two biopolymers, diutan gum, and scleroglucan, have the potential for extreme reservoir oil displacement applications. It is recommended to use diutan gum for oil displacement in reservoirs up to 90 °C and scleroglucan for oil displacement in reservoirs between 100 °C and 140 °C.

In the development of high-temperature and high-salinity oil fields, biopolymer scleroglucan flooding technology faces significant challenges. Traditional scleroglucan products exhibit poor injectability and high extraction costs. This study investigated the application potential of the original fermentation broth of exopolysaccharides (EPS) produced by microorganisms in a simulated high-temperature and high-salinity oil reservoir environment. The polysaccharide was identified as scleroglucan through IR and NMR analysis. Its stability and rheological properties were comprehensively evaluated under extreme conditions, including temperatures up to 150 °C, pH levels ranging from 1 to 13, and salinities up to 22 × 10⁴ mg/L. The results demonstrated that EPS maintained excellent viscosity and stability, particularly at 76.6 °C and 22 × 10⁴ mg/L salinity, where its viscosity remained above 80% for 35 days. This highlights its significant viscoelasticity and stability in high-temperature and high-salinity oil reservoirs. Additionally, this study, for the first time, examined the rheological properties of the original fermentation broth of scleroglucan, specifically assessing its injectability and enhanced oil recovery (EOR) performance in a simulated Middle Eastern high-temperature, high-salinity, medium-low permeability reservoir environment. The findings revealed an effective EOR exceeding 15%, confirming the feasibility of using the original fermentation broth as a biopolymer for enhancing oil recovery in extreme reservoir conditions. Based on these experimental results, it is concluded that the original fermentation broth of Athelia rolfsii exhibits superior performance under high-temperature and high-salinity conditions in medium–low permeability reservoirs, offering a promising strategy for future biopolymer flooding in oil field development.

The chemically synthesized polymer polyacrylamide (HPAM) in conventional reservoirs has achieved excellent oil displacement, but its oil displacement is poor in extreme reservoir environments. To develop biopolymer oil flooding agent under extreme reservoir conditions, the viscosity increasing and rheological properties of three biopolymers, diutan gum, xanthan gum, and scleroglucan, were studied under extreme reservoir conditions (high salt, high temperature, strong acid, and alkali), and the effects of temperature, mineralization, pH, and other factors on their viscosities and long-term stability properties were analyzed and compared. The results showed that under the temperature of 90℃ and below, the three kinds of biopolymers had the best viscosity-increasing ability. The viscosity of the three kinds of biopolymers was 80.94, 11.57, and 59.83mPa·s, respectively, when the concentration was 1500mg/L and the salinity was 220g/L. At the shear rate of 250s-1,100℃~140℃, scleroglucan has the best viscosification. At 140℃, the solution viscosity is 19.74mPa·s, and the retention rate can reach 118.27%. The results of the long-term stability study showed that the solution viscosity of scleroglucan with mineralization level of 220 mg/L was 89.54% viscosity retention in 40 days, and the diutan gum could be stabilized for 10 days, and the viscosity was maintained at 90 mPa·s. All three biopolymers are highly acid and alkali-resistant, with viscosity variations of less than 15% in the pH3~10 range. Rheological tests have shown that both of them have better viscoelastic properties than xanthan gum due to the peculiar double-helix structure of xanthan gum and the rigid triple-helix structure of scleroglucan. Therefore, the two biopolymers, diutan gum, and scleroglucan have the potential for extreme reservoir oil displacement applications, and it is recommended to use diutan gum for oil displacement in reservoirs up to 90℃ and scleroglucan for oil displacement in reservoirs between 100℃ and 140℃.

The study of seepage laws during microbial enhanced oil recovery helps to elucidate the mechanisms behind microbial flooding, and the use of large-scale physical simulation experimental devices can more objectively and accurately investigate the seepage laws of microbes in porous media, and evaluate the oil displacement efficiency of microbial systems. In this study, physical simulation experiments of microbial flooding were conducted via a slab outcrop core, and the biochemical parameters such as the concentration of Bacillus subtilis, nutrient concentration, surface tension, and displacement pressure data were tracked and evaluated. The analysis revealed that the characteristics of the pressure field change during microbial flooding and elucidates the migration rules of microbes and nutrients, as well as the change rule of surface tension. The results show that after the microbial system is injected, cells and nutrients are preferentially distributed near the injection well and along the main flow paths, with the bacterial adsorption and retention capacity being greater than those of the nutrient agents. Owing to the action of microorganisms and their metabolites, the overall pressure within the model increased, From the injection well to the production well, the pressure in the model decreases stepwise, and the high-pressure gradient zone is mainly concentrated near the injection well. The fermentation mixture of Bacillus subtilis increased the injection pressure by 0.73 MPa, reduced the surface tension by up to 49.8%, and increased the oil recovery rate by 6.5%.

High-temperature and high-salinity reservoirs (typically referring here to temperatures ≥ 100 °C and salinities > 100 g/L) impose stringent requirements on chemical flooding and profile-control agents, particularly in terms of thermal stability, salt tolerance, injectivity, and environmental compatibility. In this study, a bio-based composite mobility-control and oil-displacement system was developed by combining carbonized corn-straw particles with the biopolymer scleroglucan. Corn-straw biomass particles were prepared by pyrolysis at 500 °C followed by ball milling for 2 h. Their particle-size distribution, elemental composition, and suspension stability were characterized, and the rheological behavior, thermal and salt tolerance, long-term aging stability, injectivity, plugging performance, and enhanced-oil-recovery efficiency of the composite system were evaluated systematically. The average particle size decreased from 25.6 μm for mechanically ground straw to 2.8 μm after carbonization and ball milling. The H/C atomic ratio of the carbonized particles was 0.31, indicating enhanced aromatization and structural stability. A scleroglucan concentration of 1000 ppm provided a suspension rate of 97%, balancing suspension stability and chemical dosage. The composite system maintained stable viscosity and viscoelasticity from 30 to 130 °C in deionized water, saturated NaCl solution, and saturated CaCl₂ solution, with viscosity loss below 10%. After sealed anaerobic aging at 100 °C for 28 days, the viscosity retention remained above 90%. Sand-pack tests showed stable injectivity in media with permeabilities of 1235 and 2064 mD and a plugging efficiency of 95.7% in a 2846 mD model. In oil-displacement experiments, the composite system increased the final recovery factor from 46.6% for scleroglucan flooding alone to 53.3%, corresponding to an additional 6.7 percentage points. These results demonstrate that the carbonized biomass particle-scleroglucan system has promising thermal stability, salt tolerance, plugging capacity, and oil-displacement performance, providing a potential green strategy for mobility control in harsh reservoir environments.