Titanium alloy has extensive applications in numerous fields, such as in aerospace, shipbuilding, petrochemical, and bio-medical. However, under the condition of high temperature (above 700 °C), it is difficult to meet the requirements of the performance of the turbine blades, piston rings, valves, etc. In this paper, the alloy powder is composed of Ni60A, TiN, Al, and Si in accordance with the proportion of 1:3:4:2 (mass ratio), and the composite coating, such as TiN, TiB, Ti₅Si₃, and Al₃Ti were synthesized on Ti-6Al-4V alloy by Yttrium Aluminium Garnet(YAG) laser. The friction and wear experiments were carried out on Ti-6Al-4V alloy and alloyed coatings at different loads (3N, 6N, 9N), and different temperatures (25 °C, 350 °C, 700 °C). The impact of load and temperature on wear performance were analyzed by analyzing the friction traces. The results showed that the abrasion loss, wear width, and depth, wear volume, and wear ratio of the alloyed coatings were less than Ti-6Al-4V alloy, and the surface of furrow was shallow and the wear was less. However, under high temperature conditions, the alloy coating wears worse than Ti-6Al-4V alloy, and the high temperature wear resistance is not ideal.

The 3.6C-20Cr-Fe-(0–2.32)V high chromium cast iron (HCCI) hardfacing layers were deposited on low alloy steel by electroslag surfacing. The microstructure of hardfacing layers were observed and the carbide types, size and area fraction were measured. In addition, the hardness and wear resistance were tested. Results show that the interface between hardfacing layer and low alloy steel is defect free. 3.6C-20Cr-Fe hardfacing layer contains primary carbides and eutectic. Increasing V wt % in the hardfacing layer, primary carbides are decreasing by increasing eutectic along with martensite formation. For 1.50 wt % of V, the microstructure contains a lot of eutectic and a little of martensite. For 2.32 wt % of V, primary austenite formed, the microstructure is primary austenite, eutectic and a little of martensite. In the V alloyed hardfacing layers, V has strong affinity with carbon than chromium, hence V can replace a part of Cr in M₇C₃ and (Cr_4.4–4.7Fe_2.1–2.3V_0.2–0.5)C₃ type carbides are formed. When the V is 2.32 wt %, (Cr_0.23V_0.77)C carbides are formed in the hardfacing layer. The hardness and wear resistance are improved by increasing V from 0 to 1.50 wt %. However, when the V is 2.32 wt %, the primary austenite has reduced the hardness and wear resistance of hardfacing layer.

This paper reports a mechanism understanding how to reduce the solder joint failure phenomenon in the laser spot micro-welding process of ultra-thin steel sheets. An optimization method to improve solder joint service life is proposed. In this study, the time-dependent dynamic behaviors of the keyhole and the weld pool are simulated, and the temperatures in the keyhole of two different laser pulse waveforms are compared. The results show that laser energy attenuation mode (LEAM) can only obtain shallow weld depth because of the premature decay of the laser power of waveform, resulting in the laser beam that cannot be concentrated in the keyhole. The temperature inside the keyhole of LEAM fluctuates significantly, which shows a downward trend. Due to the existence of the peak power of waveform in laser energy continuous mode (LECM), the large angle of inclination of the wall of the keyhole inside the melt pool is more conducive to the multiple reflections of the laser beam in the keyhole and increases the absorption rate of the laser energy by the base material, resulting in the “keyhole effect”. But the temperature in the keyhole gradually rises, close to the evaporation temperature. A method combining LEAM and LECM to improve the solder joint service life by optimizing the temperature in the keyhole indirectly by adjusting the peak power of the laser pulse waveform is proposed in this study. The experimental results show that the weld depth can be optimized from 0.135 mm to 0.291 mm, and the tensile strength can be optimized from 88 MPa to 288 MPa. The bonding performance between the upper and lower plates is effectively improved. It can reach the required weld depth in a short time and improve the welding efficiency of the laser spot micro-welding process. The simulation results show that the temperature inside the keyhole is well optimized below the evaporation temperature of the material, which can avoid the violent evaporation of the welding process and keep the whole welding process in a stable state. By optimizing the laser pulse waveform, the temperature inside the keyhole can reach 3300 K, and it is always in a stable state than before optimization. The stable temperature inside the keyhole can help to reduce violent oscillation and spattering of the molten pool and improve welding efficiency and joint life. The research can help provide effective process guidance for the optimization of different laser pulse waveforms in the micro-welding process.

The local dry underwater laser welding of cp-Ti, with air as an assisting gas, and in a simulated underwater facility was researched, aiming to find a viable and economical method for repairing titanium alloy underwater vehicles in situ in the future. Macro-morphology, microstructure, and microhardness of the cp-Ti laser welds, as a function of welding parameters, were experimentally characterized. The oxidation and hardening behaviors of the welds were also studied in detail. It was found that local dry underwater laser welding with air assisted blowing is feasible for obtaining a complete and glossy weld. Compared with a weld in atmosphere, the cross-section morphology of the weld was almost unaffected by the special underwater welding environment. The weld presented a three-layer structure. High temperature and high pressure water vapor and local blowing are the direct causes of weld oxidation, and porosity defects further aggravate the oxidation behavior. The oxygen-enriched areas were mostly concentrated in the top area of the weld center and near the fusion zone, because of the higher number of grain boundaries and phase boundaries. In addition, the partial oxidation caused by local blowing and water vapor atmosphere, and also the higher strength acicular martensite caused by the rapid cooling effect of water, will lead to weld hardening. However, adjusting the welding process parameters, such as increasing the welding speed, can effectively reduce the microhardness of the weld. Our findings can provide an understanding of the influence of water environment on underwater laser welding, and verify the feasibility of a more economical method for the in situ repair of large underwater facilities.

Titanium alloy is an important material for the manufacture of key components of deep-sea submersibles. High-power vacuum laser welding is an important method for welding TC4 thick plate (40–120 mm) structures. However, due to the low melting point of aluminum, its uneven distribution in the weld caused by evaporation during welding affects the quality of joints. This paper conducted experimental and simulation studies to investigate the effect of process parameters on multi-component evaporation and uneven aluminum distribution. Based on a three-dimensional model of vacuum laser welding, the mechanism of the uneven distribution of aluminum in the weld is explained. The results show that the uneven distribution of aluminum in the weld is mainly related to the metal vapor behavior and keyhole morphology. As the welding speed rises from 1 m/min to 3 m/min, the proportion of aluminum in the metal vapor and the degree of compositional unevenness increase. When the laser power increases from 6 kW to 18 kW, the proportion of aluminum in the metal vapor and degree of unevenness increase, peak at 12 kW, and then decrease. This work facilitates the selection of suitable process parameters to reduce aluminum evaporation during the high-power vacuum welding of Ti-6Al-4V alloys. Joints with a more stable performance can be obtained by avoiding the uneven distribution of aluminum.

In the process of laser welding, the uneven distribution of solute elements caused by element burning loss and flow of molten pool affects the quality of joints. In this paper, butt welding experiments were conducted on the 3 mm thick Ti–6Al–4V specimens with different preset ratios of Al and Si powders by using 4 kW fiber laser. The distribution of Al solute element and its influence on the microstructure and mechanical properties of the final weld joint were investigated. The results showed that the self-diffusion of Al element and the flow of molten pool affects the alloy elements distribution in laser welding. And the microhardness of the welded joint with Ti–6Al–4V and 90% Al + 10% Si powders was significantly higher than that with only Ti–6Al–4V, with the difference of about 130HV. At the same time, in the joint with 90% Al and 10% Si powders, the acicular α’ size was finer, and basketweave microstructure was present as well. This research is helpful to better understand the distribution of Al solute element and its influence on the joint quality during laser welding of Ti–6Al–4V alloy, which provides a certain reference for improving the weld or surface properties of Ti–6Al–4V alloy during laser processing.