Tao Zhou

Tao Zhou

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2013 in Water Science & Technology
Verified
Journal Article
Closed access
PDF file
XHXiaofeng Huang
Xiaofeng Huang
YWYanfu Wei
Yanfu Wei
TZTao Zhou
Tao Zhou
YQYangsong Qin
Yangsong Qin
KGKunyang Gao
Kunyang Gao
XDXinyue Ding
Xinyue Ding
With increasing consumption of phosphate rock and acceleration of global phosphate production, the shortage of phosphate resources is increasing with the development and utilization of phosphate. China's Ministry of Land and Resources has classified phosphate as a mineral that cannot meet China's growing demand for phosphate rock in 2010. The phosphorus chemical industry is one of the important economic pillars for Yunnan province. Yellow phosphorus production in enterprises has led to a significant increase in the amount of phosphorus sludge. This paper focuses on phosphine generation in the process of phosphoric sludge utilization, where the flame retardant tetrakis (hydroxymethyl) phosphonium chloride (THPC) is synthesized by high concentrations of phosphine. The optimum conditions are determined at a space velocity of 150 h(-1), a reaction temperature of 60 °C, 0.75 g of catalyst, and a ratio of raw materials of 4:1. Because of the catalytic oxidation of copper chloride (CuCl2), the synthesis of THPC was accelerated significantly. In conclusion, THPC can be efficiently synthesized under optimal conditions and with CuCl2 as a catalyst.

26 April 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
TZTao Zhou
Tao Zhou
WHWei Huang
Wei Huang
CCCongyan Chen
Congyan Chen
Selective laser melting (SLM) technology is a promising additive manufacturing technology. However, due to the numerous influencing factors in this complex process, a reliable real-time method is needed to monitor the forming process of SLM. The molten pool is the smallest forming unit in the SLM process, the consistency of which can effectively reflect the quality of the printing process. By using a coaxial optical path structure and a compound amplifier circuit, high-speed acquisition of molten pool radiation can be realized. Next, single factor analysis and orthogonal experimentation were used to investigate the influence levels of key process parameters on the radiation of molten pool. In addition, numerical simulation was carried out with the same parameter setting schemes, the results of which are consistent with those in radiation detection experiments. It is shown that the laser power has the greatest effect on the radiation of the molten pool, while the scanning speed and the hatch spacing have little effect on the radiation. Finally, the positioning experiment involving the small hole structure was carried out, and the experimental results showed that the device could accurately locate the position coordinates of the given hole structure.

3 December 2023 in Metals
Verified
Journal Article
Open access
PDF file
CCCongyan Chen
Congyan Chen
TZTao Zhou
Tao Zhou
WHWei Huang
Wei Huang
WWWentong Wang
Wentong Wang
As an emerging additive manufacturing technology with potential, selective laser melting (SLM) technology is one of the current mainstream additive manufacturing processes. Many complex conditions affect the quality of the SLM products, such as extremely short forming time, rapidly changing forming environment, and micron-level melting area. Numerical simulation and a printing experiment were used to study the influence of typical technological parameters on the forming quality of SLM products, where TA1 was used as the printing material. The typical technological parameters mainly considered laser power, laser scanning speed, hatch spacing, and laser energy density. Simulation analysis was based on the maximum temperature and the size of the molten pool, and the printing experiment was focused on the parameter design methods for typical processes and the forming quality of printed products. The results show the following: (1) An increase in laser power and laser energy density can significantly improve the forming quality. However, excessive input energy will lead to poor surface quality; (2) Scanning speed and hatch spacing need to be selected according to the size of the molten pool, which mainly influences the lap rate of the molten pool. The results of this study may provide some guidance for parameter setting and forming quality optimization in SLM manufacturing process.