Verification results for the LOGOS software package as applied to numerical simulations of tsunami waves are reported. The module of the LOGOS software package that is used for tsunami simulations is based on the numerical solution of three-dimensional Navier–Stokes equations. The verification included two steps. The first step involved the verification of LOGOS free-surface flow simulations on the test cases of a collapsing water column and gravity water sloshing in a tank and the known test cases of wave generation by objects falling into water or lifted out of it. The verification of LOGOS specifically for tsunami simulations was performed using a reference set of international benchmarks including the propagation and run-up of a single wave onto a flat slope and a vertical wall, the sliding of a wedge-shaped body down a slope, flow around an island and wave run-up over an obstacle. The results of the verification simulations demonstrate that LOGOS provides sufficient accuracy in numerical simulations of tsunami waves, namely, their generation, propagation and run-up.
Verification problems and numeric simulation of cavitation processes with the help of LOGOS computational fluid dynamics software are presented in this article. The Volume of Fluid method realized within LOGOS allowing numerical simulation of double-phase problems with a free surface is used for numeric simulation. Cavitation is resolved by updating the method with the account for interphase mass exchange; its condensation and evaporation parameters are calculated with the use of the Schnerr–Sauer and Zwart–Gerber–Belamri cavitation models. Numerical simulation results of most actual test problems considering turbulence and having reliable numerical data are presented, including simulations of flow around cylinders with flat and hemispherical end surfaces for various cavitation numbers. Numerical simulation results are presented for the process of rotation of a VP1304 screw propeller in the cavitational mode. Numerical experiments prove the operability of the implemented method.
The report presents the approach implemented in the Russian LOGOS software package for the numerical simulation of the marine propeller flow problems using unstructured computational meshes automatically generated by the mesh generator. This approach includes a computational model based on the Navier–Stokes equation system and written with respect to the physical process: the turbulent nature of flow with transient points is accounted using the Reynolds Averaged Navier–Stokes method and the k–ω SST model of turbulence by Menter along with the γ–Reθ (Gamma Re Theta) laminar-turbulent transition model; the Volume of Fluid method supplemented with the Schnerr–Sauer cavitation model is used to simulate the cavitation processes; a rotating propeller is simulated by a moving computational mesh and the GGI method to provide conformity of the solutions on adjacent boundaries of arbitrarily-shaped unstructured meshes of the two domains. The specific features of the numerical algorithms in use are described. The method validation results are given; they were obtained because of the problems of finding the performance curves of model-scale propellers in open water, namely the problems of finding the performance of propellers KP505 and IB without consideration of cavitation and the performance of propellers VP1304 and C5 under cavitation conditions. The paper demonstrates that the numerical simulation method presented allows for obtaining sufficiently accurate results to predict the main hydrodynamic characteristics for most modes of operation of the propellers.
Two methods of accounting for the motion of the bodies—the deforming mesh method and the method of overlapping meshes (or overset mesh method)—are compared using problems with floating bodies, which are typical for the shipbuilding industry. Three problems are considered: oscillation of the cylinder on the water surface, movement of the box under the influence of waves, and heaving and pitching of the ship model in head waves. Numerical computations are carried out in the LOGOS software package, the simulation methodology used is based on the solution of a system of Reynolds-averaged Navier-Stokes equations, and the Volume of fluid (VOF) method to take into account the free surface. In all problems, the characteristics of the movement of bodies are evaluated; the resistance force of the ship model is also determined in the third problem; control values obtained using two methods of accounting for moving bodies are compared with the available experimental data. The results of numerical simulation have shown that both methods predict body movement parameters well; the accuracy in determining the resistance force in the task of streamlining the ship’s hull is also comparable: the difference between the maximum deviations of the resistance coefficient in the computations with deformation and overlapping computation meshes is 0.5%. In the case of computations of the three-dimensional problem, the time spent when using the mesh-deformation method turned out to be 10% more; therefore, the method of overlapping meshes can be considered more optimal when solving such shipbuilding tasks as self-propelled tests and streamlining the ship’s hull with and without wind and wave loads.