Jean-Benoit Lévesque

Mr. Jean-Benoit Lévesque


Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2017 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
MSM. Smith
M. Smith
JLJean-Benoit Lévesque
Jean-Benoit Lévesque
LBL. Bichler
L. Bichler
DSD. Sediako
D. Sediako
JGJ. Gholipour
J. Gholipour
Priti WanjaraPriti Wanjara
Priti Wanjara

1 July 2017 in International Journal of Fatigue
Verified
Journal Article
Closed access
PDP.-A. Deschênes
P.-A. Deschênes
JLJ. Lanteigne
J. Lanteigne
YVY. Verreman
Y. Verreman
DPD. Paquet
D. Paquet
JLJean-Benoit Lévesque
Jean-Benoit Lévesque
MBM. Brochu
M. Brochu

14 February 2015 in Welding in the World
Verified
Journal Article
Closed access
PDF file
MPMathieu Paquin
Mathieu Paquin
DTDenis Thibault
Denis Thibault
PBPhilippe Bocher
Philippe Bocher
JLJean-Benoit Lévesque
Jean-Benoit Lévesque
YVYves Verreman
Yves Verreman
KSKenji Shinozaki
Kenji Shinozaki

1 July 2017 in International Journal of Fatigue
Verified
Journal Article
Closed access
JCJean-Loup Curtat
Jean-Loup Curtat
JLJacques Lanteigne
Jacques Lanteigne
HCHenri Champliaud
Henri Champliaud
ZLZhaoheng Liu
Zhaoheng Liu
JLJean-Benoit Lévesque
Jean-Benoit Lévesque

1 August 2016 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
SSSheida Sarafan
Sheida Sarafan
JLJean-Benoit Lévesque
Jean-Benoit Lévesque
Priti WanjaraPriti Wanjara
Priti Wanjara
JGJ. Gholipour
J. Gholipour
HCH. Champliaud
H. Champliaud
Heavy-section assembly of hydroelectric turbine runner materials using single-pass, autogenous EBW was demonstrated to penetrate a 90-mm-thick butt joint. The welding-induced distortions and residual stresses were characterised to understand the impact of the materials and process conditions (e.g. preheating and/or PWHT). Using 3D optical measurements, the angular distortions of EB-welded UNS S41500 and CA6NM steels were determined to be 0.13° and 0.38°, respectively. The longitudinal residual stresses, measured through the contour method, had a M-shaped distribution throughout the thickness with minimum (∼−500 MPa) compressive stresses in the FZ and maximum (∼600 MPa) tensile stresses in the HAZ. After PWHT, the tensile and compressive stresses reduced to ∼100 MPa.

23 December 2019 in Metallurgical and Materials Transactions A
Verified
Journal Article
Open access
PDF file
JLJean-Benoit Lévesque
Jean-Benoit Lévesque
JLJ. Lanteigne
J. Lanteigne
HCHenri Champliaud
Henri Champliaud
DPD. Paquet
D. Paquet
Fatigue damage is commonly encountered by operators of Francis type hydraulic turbine runners made of 13Cr-4Ni soft martensitic stainless steel. These large and complex welded casting assemblies are subjected to fatigue crack initiation and growth in the vicinity of their welded regions. It is well known that fatigue behavior is influenced by residual stresses and the microstructure. By including solid-state phase transformation models in welding simulations, phase distribution can be evaluated along with their respective volumetric change and their effect on residual stresses. Thus, it enables the assessment of welding process on fatigue crack behavior by numerical methods. This paper focuses on modeling solid-state phase transformations of 13Cr-4Ni soft martensitic stainless steel, used for manufacturing hydraulic turbine runners, occurring upon welding. It proposes to determine the material parameters of the models for both the austenitic and the martensitic transformation by nonisothermal dilatometry tests. The experiments are conducted in a quenching dilatometer with applied thermal conditions as experienced in the heat-affected zone of homogeneous welds. The activation energy and the kinetic parameters of the austenitic transformation from fully martensitic state are measured from the experimental results. The martensitic transformation modeling from a fully austenitic domain is also presented.