Pierpaolo Iovane

Dr. Pierpaolo Iovane

ENEA Portici Research Centre, Naples, Campania, Italy
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2013 in Waste Management
Verified
Journal Article
Closed access
Sabrina PortofinoSabrina Portofino
Sabrina Portofino
ADAntonio Donatelli
Antonio Donatelli
PIPierpaolo Iovane
Pierpaolo Iovane
CICarolina Innella
Carolina Innella
RCRocco Civita
Rocco Civita
SGSergio Galvagno
Sergio Galvagno

1 February 2018 in Resources, Conservation and Recycling
Verified
Journal Article
Closed access
AMAntonio Molino
Antonio Molino
ADAntonio Donatelli
Antonio Donatelli
TMTiziana Marino
Tiziana Marino
AAAlfredo Aloise
Alfredo Aloise
JRJuri Rimauro
Juri Rimauro
PIPierpaolo Iovane
Pierpaolo Iovane

29 April 2011 in Energy & Fuels
Verified
Journal Article
Closed access
SPSabrina Portofino
Sabrina Portofino
SCStefania Casu
Stefania Casu
PIPierpaolo Iovane
Pierpaolo Iovane
ARAntonio Russo
Antonio Russo
MMMaria Martino
Maria Martino
SGSergio Galvagno
Sergio Galvagno

23 July 2024 in Polymers
Verified
Journal Article
Open access
PDF file
LTLoredana Tammaro
Loredana Tammaro
Alfonso MartoneAlfonso Martone
Alfonso Martone
BPBarbara Palmieri
Barbara Palmieri
CBCarmela Borriello
Carmela Borriello
Sabrina PortofinoSabrina Portofino
Sabrina Portofino
SGSergio Galvagno
Sergio Galvagno
The use of 3D printing technology for manufacturing new products based on sustainable materials enables one to take advantage of secondary raw materials derived from recycling. This work investigates the structural performances of 3D printing composite filaments based on polylactic acid (PLA), as a matrix, reinforced by recycled carbon fiber (rCF). Carbon fibers were recovered from industrial scraps by a patented thermal process and used to produce thermoplastic composite filaments for additive manufacturing without any additional treatment and additives. The influence of the recovered carbon fiber (rCF) content on the thermal properties, mechanical properties and microstructure of the composites was studied in the range of 3–20 wt%. The recorded TGA curves exhibited a one-stage weight loss within the temperature range 290–380 °C for all samples and the residual rCF content was in good agreement with the theoretical fiber loading. The Young modulus of the extruded filaments strongly increased below a critical content (5 wt%), while at higher content the improvement was reduced. An increase in the storage modulus of 54% compared to neat PLA 3D printed sample resulted in a printed specimen with a higher rCF content. SEM images highlighted a strong rCF prevailing alignment in the direction of the extrusion flow, creating almost unidirectional reinforcement inside the filament. These findings suggest that homogeneous composite filaments reinforced with well-dispersed recycled CF without additional chemical modification and additives are suitable materials for additive manufacturing. The effect of rCF topological distribution within the material on the mechanical performances has been discussed, highlighting that the isolated fibers could efficiently transfer loads with respect to the percolated 3D network and have been correlated with the microstructure.

1 August 2019 in Journal of Physics and Chemistry of Solids
Verified
Journal Article
Closed access
MSMaria Sarno
Maria Sarno
SGSergio Galvagno
Sergio Galvagno
CSCarmela Scudieri
Carmela Scudieri
PIPierpaolo Iovane
Pierpaolo Iovane
SPSabrina Portofino
Sabrina Portofino
CCClaudia Cirillo
Claudia Cirillo

23 January 2024 in Plasma
Verified
Journal Article
Open access
PDF file
PIPierpaolo Iovane
Pierpaolo Iovane
CBCarmela Borriello
Carmela Borriello
GPGiuseppe Pandolfi
Giuseppe Pandolfi
Sabrina PortofinoSabrina Portofino
Sabrina Portofino
Gabriella RamettaGabriella Rametta
Gabriella Rametta
SGSergio Galvagno
Sergio Galvagno
The production of spherical powders has recently registered a boost due to the need to fabricate new printing materials for Additive Manufacturing applications, from polymers and resins to metals and ceramics. Among these materials, stainless steels powders play a leading role, since they are widely used in industry and everyday life; indeed, micron-sized spherical stainless steel powders have specific characteristics and are considered as one of the best candidates for Additive Manufacturing systems and for application in a wide range of sectors. In this paper, stainless steel 316 L powders were used to explore and identify the best process parameters of a thermal plasma process able to produce spherical powders for Additive Manufacturing applications. X-ray Diffraction, Scanning Electron Microscopy, Particle Size Distribution and Flowability analysis were performed to characterize reagents and products. Powders with a high circularity (>0.8) and improved flowability (<30 s/50 g) were successfully obtained. The collected results were compared with data available from the literature to identify the potential use of the spherical produced powders.