A precise prediction of the cure-induced shrinkage of an epoxy resin is performed using a finite element simulation procedure for the material behaviour. A series of experiments investigating the cure shrinkage of the resin system has shown a variation in the measured cure-induced strains. The observed variation results from the thermal history during the pre-cure. A proposed complex thermal expansion model and a conventional chemical shrinkage model are utilised to predict the cure shrinkage observed with finite element simulations. The thermal expansion model is fitted to measured data and considers material effects such as the glass transition temperature and the evolution of the expansion with the degree of cure. The simulations accurately capture the exothermal heat release from the resin and the cure-induced strains across various temperature profiles. The simulations follow the experimentally observed behaviour. The simulation predictions achieve good accuracy with 2–6% discrepancy compared with the experimentally measured shrinkage over a wide range of cure profiles. Demonstrating that the proposed complex thermal expansion model affects the potential to minimise the shrinkage of the studied epoxy resin. A recommendation of material parameters necessary to accurately determine cure shrinkage is listed. These parameters are required to predict cure shrinkage, allow for possible minimisation, and optimise cure profiles for the investigated resin system. Furthermore, in a study where the resin movement is restrained and therefore able to build up residual stresses, these parameters can describe the cure contribution of the residual stresses in a component.
Defining the specific cure profile of thermosetting polymers is an important aspect in many applications where the mechanical performance and appearance of components can be affected. Cure-induced strains or stresses from the shrinkage of thermosets lead to reduced performance due to accelerated damage or discarded products due to distortions. This research focuses on validating a proposed modelling framework, simulating the load-transferring part of the curing process affecting the mechanical performance. The model's accuracy is evaluated against experimental results, and the model prediction is found to be within an accuracy of 2-8% of the experimental results. A 16-hour and 31-hour two-stage cure profile was compared and validated experimentally. The short profile results in a higher cure-induced of -0.56% with the longer profile yielding -0.46% cure-induced strain. Based on the model, a new three-stage cure profile has been proposed. Using this, it is possible to achieve a low level of cure-induced strain of -0.45% at a shorter cure time on 18 h.
1 November 2023 in IOP Conference Series: Materials Science and Engineering
In the wind industry, the increasing length of turbine blades and the use of thick composite sections make it vital to understand the thermoset and the underlying curing process. In this study, the curing of a specific thermoset epoxy for application in wind turbine blades is characterised by differential scanning calorimetry. The thermoset is analysed under dynamic and isothermal conditions to determine the complex cure behaviour under these various conditions. The data is fitted to determine firstly; the cure kinetics of the material through a kinetic model. Secondly; the phenomenon of the glass transition temperature Tg is studied to predict the development of Tg as a function of the degree of cure. Thirdly, a Diffusion-Kinetic model was utilised to make more accurate cure predictions based on the interaction between kinetic chemical reactions and diffusion control affecting the reaction rate through the incorporation of the glass transition temperature. A simple experimental framework for validating the diffusion-kinetic model was used to make a final validation of the model predictions on a larger scale. A set of final parameters is presented for application in a full diffusion-kinetic model for cure predictions and simulations beyond this study.
A small experimental setup for in-situ measurement of the load-transferring strains during the curing process of thermosets is proposed. Combining the output from an unconstrained and a kinematically constrained setup, it is possible to design a cure profile for the first time, lowering the residual stresses in the final product while keeping the cure time short based on the output from a few simple experiments. The stress relaxation during the curing process under a kinetically constrained condition is accounted for by comparing the final cure-induced strain during a kinetically unconstrained and constrained cure experiment. The constrained polymer is curing between two laminates where the constraining layer is removed after finalizing the cure profile, making it possible to measure the final cure-induced strain for that case as well. The temperature at which the load-transferring point is reached is found to be a key process parameter from which the final cure-induced strains can be predicted for the unconstrained case. From the corresponding constrained cure experiments, the final residual stresses can be measured.
This work uses predictive modeling to study the phenomenon of cure‐induced wrinkles based on validated experimental model behavior. The mechanisms that govern the occurrence are studied with emphasis on the need for thermal gradients, causing a variation in thermal expansion and build‐up of stiffness across a large monolithic composite laminate to create cure‐induced wrinkles. The appearance of wrinkles was evaluated based on the undulated region's maximum amplitude, angle, and wavelength. The angle is especially important for understanding the structural behavior of the composite material after curing. Boundary conditions were found to affect the wrinkle amplitude and angle. Especially, constraining the laminate against expansion was found to increase the rate at which a wrinkle appears. The pre‐cure temperature was found to be the most important parameter to control, as the predictions show that slight variations in the pre‐cure temperature greatly influence the angle of the undulated fibers in the laminate. This shows the need for accurate temperature control and the need for uniform temperature across the mold to mitigate wrinkles in the curing process.
1 October 2025 in IOP Conference Series: Materials Science and Engineering
This work provides insights into wrinkle formation due to the thermomechanical nature of curing in thick and long monolithic composite laminates. The investigations focus on two main factors: geometrical imperfections and thermal gradients across the mould. Firstly, the effect of geometrical imperfections was examined in terms of imperfection length and amplitude. Although geometrical imperfections showed a little effect on the angle and amplitude of the wrinkle, the geometrical imperfection was found to have no governing influence on the formation of wrinkles. Secondly, the effect of thermal gradients was assessed by varying the length of a non-heated region in the mould. The effect of varying the length of this region was found to be significant and therefore a governing parameter in the occurrence of wrinkles induced by curing. The effects were found to be as high as 63-70% change of the key wrinkle parameters defined by the wrinkle amplitude and resulting change in fibre undulation. Demonstrating that thermal gradients within the mould play a significant role in wrinkle formation during the curing process of composite manufacturing.